Bark On or Bark Off
Bark looks good in photographs and falls off in living rooms. How to decide and how to remove it cleanly.
Bark on a slab is the thing people fall in love with in the photograph and the thing that is on the floor eighteen months later. It is worth deciding deliberately rather than by default.
Why bark lets go
Between the bark and the wood is the cambium, the thin growing layer. In a living tree it is wet and soft. In a dried slab it is a dry crumbly layer with almost no strength, and the bark is held on by not very much. Then the wood shrinks as it dries further in a heated house, the bark does not shrink at the same rate, and the bond fails.
How well it holds depends mostly on when the tree was felled. Winter-felled timber, cut when the sap is down, holds its bark far better than summer-felled timber. You rarely know which you have.
The honest comparison
| Bark on | Bark off | |
|---|---|---|
| Look | Dramatic, raw, photographs well | Clean, shows the sapwood line and the true edge profile |
| Longevity | Unpredictable, often fails in a few years | Permanent |
| Maintenance | Pieces come off, dust collects behind it | Same as the rest of the edge |
| Insects | Bark is where borers live; it can harbour them | Removes the habitat entirely |
| Cleaning | Awkward, cannot be wiped | Vacuum or wipe |
| Best for | Pieces rarely touched: a console, a wall shelf | Dining tables, desks, islands, benches, anything used |
For anything people sit at, eat at or brush past, take the bark off. The edge underneath is the interesting part anyway: the sapwood line, the wave of the growth, the texture of the cambium face. Bark hides it.
If you keep it
- Test every section. Press and tug along the whole length. Anything that moves now will come off later. Remove those sections rather than hoping.
- Consolidate the edges. Thin penetrating resin wicked into the join between bark and wood stabilises it considerably. This is the main reason some bark survives.
- Seal it. Bark takes finish like a sponge and still needs it, both for appearance and to slow moisture movement.
- Accept the dust trap. Vacuum with a brush attachment and do not expect to clean behind it.
Taking it off cleanly
- Do it early. Before flattening, before sanding, long before any finish. Bark removed after finishing leaves an unfinished line and a colour mismatch.
- Start at a loose end. Work a stiff putty knife or a drawknife into the cambium layer and lever along the length. Well-bonded bark fights; most does not.
- Work with the grain direction so you are not tearing fibres out of the sapwood underneath.
- Brass brush the cambium residue. There will be a layer of soft dark crumbly material left. A brass brush in a drill, run along the edge, takes it back to sound wood and leaves the natural texture.
- Pick out the pockets and blow with compressed air.
- Then treat it as a normal live edge, following finishing the live edge itself.
Insects
Bark is where most wood-boring insects live and lay. Kiln drying kills what is in the timber, which is part of why our slabs are kiln dried to 8 to 10 percent rather than air dried, a difference covered in kiln dried versus air dried. Even so, removing bark removes the material most likely to shed frass and hold eggs, and it is the standard advice for furniture that lives indoors.
What the edge looks like underneath
People worry the edge will look bare. It does not. Under the bark is the cambium face: a smooth, undulating surface that follows every bulge and hollow of the trunk, usually paler than the heartwood. On walnut, that pale sapwood against the dark heart is one of the best things about the species, discussed in sapwood versus heartwood.
Common questions
Should I remove the bark from a live-edge slab?
For anything in daily use, yes. Bark is held on by a weak crumbly layer and usually releases within a few years in a heated house. Keep it only on pieces that are rarely touched.
How do you remove bark from a slab?
Lever it off along the cambium layer with a stiff putty knife or drawknife, working with the grain, then clean the residue back to sound wood with a brass brush. Do it before flattening and finishing.
Can you glue bark back on?
Small sections can be consolidated with thin penetrating resin, but once bark has started releasing along a length it usually continues. Removing it is the durable answer.
Does bark attract insects?
Bark is where most wood-boring insects live. Kiln drying kills what is in the timber, and removing the bark removes the material most likely to harbour eggs and shed frass.