Butterfly Keys and Crack Repair

How a bowtie key stops a crack spreading, where to place it, and when a key is decoration rather than structure.

Finishing and care7 min readUpdated 2026-10-23

A butterfly key, also called a bowtie or a dutchman, is a double-dovetail shaped piece of wood let into the face of a slab across a crack. The waist sits over the crack and the two flared ends grip the wood on either side. Pull the halves apart and the key has to be torn out or broken before the crack can open further.

They have become a visual signature of slab furniture, which means a lot of them are installed where they do nothing. Here is how to tell the difference and how to fit one that works.

First decide whether the crack needs anything

Not every split wants intervention. Work through this before you reach for the router.

  • Is it an end check? Most slabs dry with splits running in from the ends, because end grain loses moisture fastest. If the check is within the part you are going to trim off anyway, it needs nothing. Trim first, then look again.
  • Is it stable? Mark both ends of the crack with a pencil and a date. Leave it a few weeks through a change in weather. If the pencil marks still bracket the crack, it is not travelling.
  • Does it go through? A surface check on one face is cosmetic. A crack visible on both faces is structural.
  • Where is it? A crack in the middle third of a dining top is in the highest stress zone. The same crack 10 cm from an end matters much less.

More on reading splits in cracks, checks and voids: what is normal.

What a key actually does

A butterfly key resists the two halves pulling apart across the crack. It does that through the flares, which are gripping long grain on each side.

It follows that the key must be oriented across the crack, with its long axis perpendicular to the split. A key set at an angle, or parallel to the crack, is jewellery.

It also follows that grain direction in the key matters. The key's own grain should run along its long axis, from one flare through the waist to the other. A key with grain running across the waist will snap at the waist the first time the slab works, because the waist is the narrowest point and short grain has no strength.

Honest version

A key stops a crack getting longer. It does not close a crack, does not glue it, and does not stop the slab moving seasonally. If you want the crack to disappear, the answer is filling it, not keying it.

Sizing and placing them

  • Depth: a third to a half of the slab thickness. On a 6 cm top, 20 to 30 mm. Deeper is not better, and a key cut too deep weakens the wood it is supposed to be reinforcing.
  • Length: long enough that each flare has solid wood well clear of the crack, typically 10 to 15 cm on a dining top.
  • Spacing: along a long crack, place one near the leading tip and others every 20 to 30 cm. The one at the tip is the one doing the work, because that is where the crack wants to extend.
  • Both faces: on a through crack in a highly stressed area, key both the top and the underside. Nobody sees the underside ones and they double the hold.

Always put a key past the end of the crack, not just along it. Stopping the tip is the entire job.

Fitting one

  1. Make the key first. Cut it from stock thicker than the final depth so you have something to hold. Contrasting species is a design choice; the same species makes the repair quiet.
  2. Trace it in place. Position the key over the crack, hold it down and knife around it. A knife line is far more accurate than a pencil line, and it severs the surface fibres so they do not tear out.
  3. Hog out the waste. A router with a small straight bit and a depth stop, staying a couple of millimetres inside the line.
  4. Pare to the line by hand. A sharp chisel, working to the knife line, keeping the walls square. This is where the fit is won.
  5. Test, then glue. The key should need a firm tap, not a hammer. Too tight and you will split the slab driving it in. Glue the key, not the mortise walls, seat it proud, let it cure fully.
  6. Flush it off. A hand plane or a sharp chisel, then sand with the surrounding surface. Do not route it flush: it is easy to dig into the slab.

Filling versus keying

They solve different problems and are often used together.

GoalMethod
Stop the crack travellingButterfly key
Make the surface continuous and cleanableResin or a wood fill
Both, on a dining tableKey the tip, fill the void, then flatten and finish

If you fill with resin, do it before final flattening so the fill gets levelled with the surface. See filling voids and knots with resin.

When not to bother

Skip the key when the crack is short, stable, not through the thickness and not in a stressed area. A shallow check that has sat unchanged through a winter in a finished top is part of the slab's history. Routing a bowtie into it adds a repair where there was no damage, and once cut, it cannot be undone.

Common questions

Do butterfly keys actually work?

Yes, when they are sized, oriented and placed correctly: across the crack, with their own grain running along the key, and positioned past the tip of the split. Fitted decoratively at an angle, they do nothing structural.

How deep should a butterfly key be?

About one third to one half of the slab thickness. On a 6 cm top that is roughly 20 to 30 mm. Cutting deeper removes material from the wood you are trying to reinforce.

Can I just fill a crack with epoxy instead?

Filling makes the surface continuous but adds little resistance to the crack extending, because cured resin in a thin crack is a weak joint. On a stressed crack use both: a key to stop it travelling and a fill to close the surface.

Which way should the grain run in a butterfly key?

Along the long axis of the key, running through the waist from one flare to the other. Grain running across the waist leaves short grain at the narrowest point and the key will break there.

Some slabs are chosen for the crack

Natural voids, bark pockets and knot holes are listed openly with every piece, with photographs so you can plan the repair before it arrives.

See slabs with voids