Kiln Dried or Air Dried: Which to Buy

What each process does to a slab, why indoor furniture needs kiln drying, and how to spot a slab that is not ready.

Choosing a slab6 min readUpdated 2026-10-23

A freshly cut slab can be more than half water by weight. Furniture needs it at roughly 8 to 10 percent for a heated European interior. How it gets there decides whether your table is stable or a slow-motion problem.

Air drying: what it can and cannot do

Air drying means stickering the slabs under cover with air moving through them, and waiting. The rule of thumb is about a year per 25 mm of thickness, so a 6 cm slab is a two to three year proposition before it is even close.

The limit is the important part: air drying can only reach equilibrium with the outdoor air. In most of northern Europe that bottoms out around 14 to 18 percent, depending on season and location.

A heated house in winter sits far below that. Put an 16 percent slab into a 35 percent humidity room in January and it will keep drying, shrinking and moving inside your furniture, which is exactly where you do not want it to happen.

Kiln drying: what it adds

A kiln controls temperature and humidity to take the wood below what the outdoor air can achieve, and to do it on a schedule that limits damage.

Three things a proper kiln schedule does:

  • Reaches 8 to 10 percent, which is the range a heated interior needs.
  • Sterilises. A high-temperature phase kills insects and larvae in the wood. Air dried stock carries no such guarantee.
  • Relieves stress. A conditioning phase at the end equalises moisture through the thickness and relaxes case hardening, which is the stress state that makes a board pinch the saw and distort when it is cut.

That last point is why a badly kilned slab can be worse than an air dried one. A kiln run too fast produces a slab that reads dry on a meter at the surface while the core is wetter, and that is locked in stress waiting to be released when you machine it.

The combination most slabs actually get

In practice, thick slabs are usually air dried first and then finished in a kiln. Air drying does the easy, cheap part of the water removal slowly and gently, and the kiln takes it the rest of the way and conditions it.

That is the sequence to look for. Straight into a kiln from green, at thickness, is hard on a slab.

How to tell whether a slab is ready

  1. Ask for the number, the method and the date. "Kiln dried" is a claim. "Measured 9 percent with a pin meter on 12 September" is information. See moisture content explained.
  2. Ask where it was measured. A surface reading on a thick slab tells you about the surface. A pin meter with insulated probes driven deeper tells you about the core.
  3. Ask where it has been stored since. A slab dried to 9 percent and then stored in an unheated barn through a wet autumn is no longer at 9 percent.
  4. Weigh it if you can. A slab that keeps losing weight week to week indoors is still drying.

What happens if you build too early

The failure modes are predictable:

  • Shrinkage across the width, which opens gaps against anything fixed, splits the top where it is constrained, and pulls joints apart.
  • Cupping, as one face dries faster than the other.
  • Checks opening that were closed when you bought it.
  • Finish failure, because moisture moving out from underneath lifts a film finish.

None of this is repairable by refinishing. The wood has to reach equilibrium first.

Acclimatising is still required

Even a correctly kiln dried slab needs time in the room it will live in. A slab at 9 percent that has travelled in a cold lorry and sat in a garage is not at 9 percent at its surface when it arrives.

Give it two to four weeks indoors, stickered flat with air on both faces, before machining. The detail is in acclimatising a slab after delivery.

What we supply

All slabs kiln dried to 8 to 10 percent moisture content and supplied rough sawn, so your maker takes the final thickness. Measurements and the reading go out with the photographs.

Common questions

Can I use an air dried slab indoors?

Only if you let it reach equilibrium in a heated space first, which can take many months for a thick slab, and you accept it may check and move while it does. For furniture, kiln dried is the sensible purchase.

Does kiln drying change the colour?

It can. High temperature schedules darken some species, and walnut in particular can lose some of the contrast between heart and sap in a hot kiln. A gentle schedule preserves colour better.

Is kiln dried wood more brittle?

Properly dried, no meaningful difference for furniture. Over-dried or badly dried wood can be, which is a reason to ask about the schedule rather than just the end number.

How do I know the slab will not move at all?

It will move. Correct drying means it moves predictably and seasonally rather than drastically and once. Build for it: attaching a slab top to a base.

Kiln dried to 8 to 10 percent

Every slab we sell has been kiln dried and measured. Shortlist one and we send the reading along with the photographs within a day.

See slabs in stock