What 8 to 10 Percent Moisture Content Means

The number every slab listing quotes, what it predicts about movement indoors, and how to check it yourself.

Choosing a slab7 min readUpdated 2026-10-23

Every slab we list says 8 to 10 percent moisture. It is the single most important number in the listing and the one buyers most often skip past. It is not a quality grade. It is a prediction about how much the slab is going to move once it is in your house.

What the number is

Moisture content is the weight of the water in the wood, expressed as a percentage of the weight of the wood with no water in it at all. So 10 percent means a 100 kg slab is carrying about 9 kg of water.

Freshly felled timber can be well over 60 percent. Air drying in a covered stack in a northern European climate gets it down to somewhere around 15 to 20 percent and then stops, because the wood simply reaches balance with the outdoor air. A kiln takes it the rest of the way.

Why 8 to 10 and not something else

Wood is hygroscopic. It constantly exchanges water with the surrounding air until it reaches equilibrium with it, and that equilibrium point moves with the humidity of the room.

In a heated European home the indoor air swings through the year. In midwinter with the heating running, indoor relative humidity often falls low enough that wood settles at around 6 to 8 percent. In a damp summer it can climb to 11 or 12 percent. A slab dried to 8 to 10 percent is therefore sitting roughly in the middle of where it will live.

That is the whole point. The slab will still move, because the air still swings. It just moves a small distance either side of where it already is, rather than making one large journey in the first winter.

The mistake to avoid

Air-dried stock at 16 percent looks and feels dry. Brought into a heated room it will keep losing water down to 7 or 8 percent, and it will shrink, cup and check while it does. That is where most cracked slab tables come from.

How much movement does it actually predict

Wood moves very little along its length and a lot across its width. For a rough sense of scale, a one metre wide hardwood top moving between a damp summer and a dry heated winter can change by several millimetres across the grain. Oak moves more than walnut. The exact figure depends on the species, on how the board was cut out of the log, and on how far your indoor humidity actually swings.

Two things follow from that:

  • The fixing method has to let the top slide across its width. This is not optional on a solid top. See attaching a slab top so it can still move.
  • A correctly dried slab that cracks has almost always been fixed down rigidly or moved into very dry air, not badly dried.

What seasonal movement looks like in practice, month by month, is in how a slab moves through the year.

Checking it yourself

A moisture meter costs less than a tin of finish and settles arguments. There are two kinds:

  • Pin meters push two small pins into the wood and measure electrical resistance between them. They read where the pins reach, which on a short pin is the outer few millimetres.
  • Pinless meters sit flat on the surface and read a zone below it without marking the wood. Convenient, and they need the surface to be flat and the meter set for the right density.

Three habits make the reading mean something:

  1. Take several readings along the length and across the width, not one in the middle. Ends dry fastest and read lowest.
  2. Set the species correction if the meter has one. Density changes the reading.
  3. Read away from the very end. The last 10 to 15 cm of a slab is unrepresentative. If you can, read a freshly cut surface.

On a thick slab, a surface reading can be lower than the core. This is the main reason thick stock gets a longer kiln schedule and then a conditioning period to even itself out.

What a seller should be able to tell you

Ask three questions. The answers tell you more than the headline number does.

  • What does it read now, and where was it measured? A reading taken today on a freshly exposed surface is worth more than a figure from the kiln certificate two years ago.
  • How has it been stored since the kiln? A slab that has spent a winter in an unheated barn has climbed back up towards the outdoor equilibrium. It is not at 8 percent any more.
  • Was it conditioned after drying? A kiln run that ends abruptly can leave stress locked in the board, which shows up as pinching or cupping the moment it is cut.

We take the reading when the slab is listed and again before it ships, and we send it with the photographs.

What to do when it arrives

Even a correctly dried slab needs to settle into your particular room. Lay it flat, stickered so air reaches both faces, in the room it is going to live in, and leave it for at least a couple of weeks before cutting or finishing. The full routine is in the first two weeks after delivery.

Common questions

What moisture content should furniture wood be?

For indoor furniture in a heated home, somewhere in the 7 to 10 percent range. That puts the wood close to the average it will experience once the heating cycles through a year.

Is air-dried wood good enough for a table?

Not on its own. Air drying stalls near the outdoor equilibrium, which in northern Europe is well above indoor conditions. Air-dried stock needs a kiln or a long spell in a heated space before it is stable indoors.

How do I measure moisture content in a slab?

With a pin or pinless moisture meter, taking several readings along the length and across the width, with the species setting correct, and avoiding the last 10 to 15 cm at each end.

Will a slab at 9 percent still move?

Yes. Every solid wood top moves with the seasons. The point of drying to 8 to 10 percent is that the movement is small and centred, instead of one large shrink in the first heating season.

Kiln dried, measured, and measured again

Each slab is listed with its moisture reading and checked again before it goes on the pallet. Ask for the number on any piece and we will send it with the photographs.

See slabs in stock