Burl, Crotch and Figure in Slabs

Where dramatic grain comes from, why it costs more, and the extra work figured wood asks for when finishing.

Choosing a slab5 min readUpdated 2026-10-23

Figure is any grain pattern beyond straight grain. It is why two walnut slabs of the same size can differ in price by a factor of two, and it is almost entirely a function of what the tree did while it was growing.

Where figure comes from

TypeWhere it formsWhat it looks like
BurlA growth on the trunk, often a response to injury or stressDense swirling eyes and clusters, no consistent grain direction
CrotchWhere the trunk forks into two limbsA feathered, flame-like pattern spreading out from the fork
Curl or fiddlebackWavy fibre growth, often in the lower trunkHorizontal banding that shimmers and appears to move as you walk past
Ray fleckThe saw cut running close to the radial planeSilver flecks, strong in oak, dense and fine in plane
SpaltingEarly fungal activity before dryingFine black lines, as if drawn in ink

The first three are properties of the tree. Ray fleck is a property of the cut. Spalting is a property of what happened after the tree came down. They can appear together.

Why figured wood costs more

Three reasons, all real:

  • Scarcity. A burl is a growth on a small part of one tree. Crotch wood exists only where the tree forked.
  • Yield. Figured sections are often short, irregular and surrounded by wood that has to be cut away.
  • Difficulty. Wild grain is harder to machine and harder to finish, so more labour goes in per square metre.

Figure is one of the biggest levers on slab price, alongside size and species: what drives the price of a walnut slab.

The extra work figure asks for

This is the part that is rarely mentioned when the slab is sold.

  1. Tearout. In wild grain the fibre direction reverses constantly, so a planer or router lifts and tears fibres where straight grain would cut cleanly. The answers are light cuts, sharp tooling, and sanding where machining is risky.
  2. Sanding takes longer. You cannot sand with the grain when the grain goes in every direction, so you work through the grits more carefully and inspect under raking light.
  3. Burl is often unstable. Dense swirling wood with included bark and voids may need resin stabilising before it can be worked.
  4. Finish absorbs unevenly. Figured areas drink more in some places than others, so the first coat can look blotchy before it is built up.

Budget more time, not just more money, for a figured slab.

What figure does under a finish

Dry and sanded, most figure is barely visible. Curl in particular looks like nothing at all on a sanded surface and then appears the moment oil goes on, because the finish changes how light enters and reflects off the differently angled fibres.

Two consequences when buying:

  • Judge figure from a wet or oiled photograph, never a dry sanded one. A wipe of water or mineral spirits previews the finished look closely.
  • Figure moves as you move. Curl and ray fleck change with viewing angle, which a photograph cannot show. Expect the real piece to be more alive than the image.

Where figure belongs, and where it does not

  • Good: coffee tables and side tables, where the surface is seen close up and from above. Console tops. The centre of a dining table.
  • Mixed: a whole dining table in heavy burl is a lot to look at three times a day, and it fights with everything placed on it.
  • Careful: structural pieces. Wild grain means the fibres do not run continuously along the length, so a heavily figured board is not as strong along its length as a straight-grained one. For a long bench seat or a cantilever, prefer straight grain. See how far a slab can span unsupported.

Common questions

Is figured wood weaker?

Along its length, usually yes, because the fibres do not run straight from end to end. For a tabletop supported by a base this rarely matters. For a seat or a shelf spanning a gap it can.

Does spalting count as figure?

It is treated as figure in the market and priced accordingly. The difference is that spalting is decay arrested at the right moment, so soundness has to be checked with a fingernail.

Can figure be added?

No. Burl, crotch and curl are grown. Ray fleck depends on how the log was cut, which is decided at the mill. What a finish can do is reveal what is there.

Will figure fade?

The pattern does not fade, though the overall colour shifts with light over years. Curl and fleck remain for the life of the piece.

Figure is in the photographs

C16 has a deep burl pocket and a dramatic live edge. We photograph figure wet so you see what the finish will reveal.

See C16