What Drives the Price of a Walnut Slab

Length, width, thickness, figure, defects and drying all move the number. How to compare two quotes honestly.

Choosing a slab6 min readUpdated 2026-10-23

Two walnut slabs of the same length can differ in price by three times. The difference is almost never arbitrary, and understanding the levers makes it possible to spot both a bargain and an overpriced piece.

The levers, roughly in order of impact

FactorWhy it moves the price
WidthThe strongest lever. A tree that was 130 cm across at that height is rare. Width scales price faster than length does.
LengthLong slabs come from long clear trunk sections. Over 300 cm narrows the field considerably.
ThicknessMore material, and a thicker slab takes far longer to dry and carries more drying risk.
FigureBurl, crotch and curl multiply price: burl, crotch and figure.
DryingYears of yard time, kiln time and the slabs lost in the process are all in the price of the ones that survived.
DefectsReduce price where they reduce usable size. Raise desirability where they are decorative.
FlatnessA twisted slab yields less finished thickness, so it is worth less even at the same dimensions.

Why width costs more than length

A tree adds length early and width slowly. Getting a 130 cm wide slab means a trunk well over 130 cm in diameter at that point, which is many decades of growth, and such trees are not common, not easy to transport and not easy to mill.

It compounds: a wide slab is also harder to dry without cupping, needs a bigger kiln, and is more likely to be rejected after drying. So the rarity at the start is multiplied by the losses along the way.

The practical takeaway: if your piece does not need the width, do not pay for it. A desk wants 70 cm, and a 130 cm slab is the wrong purchase. See a walnut slab desk.

Comparing two quotes honestly

Price per square metre is the usual comparison and it is misleading on its own. Work out the usable piece instead:

  1. Start from the narrow point of the width, not the widest. That is what decides what you can cut.
  2. Subtract end checks that will be trimmed off the length.
  3. Subtract the thickness lost to flattening, which depends on flatness, not just on the rough dimension.
  4. Subtract any section beyond a bad split that cannot be used as one piece.
  5. Then divide the price by what is left.

A slab that looks 20 percent more expensive can easily be cheaper per usable square metre.

What else is in the number

Three costs that are real and invisible in a listing:

  • Time. A 6 cm slab air dried then kilned represents two or three years of someone's stock sitting still.
  • Losses. Not every slab survives drying. The ones that crack or twist beyond use are paid for by the ones that do not.
  • Handling. Milling, stickering, turning, moving and storing pieces that weigh over 100 kg each is not light work.

Where the bargains are

  • Narrow slabs. Everyone wants 110 cm plus for a dining table, so 70 to 85 cm slabs are better value and are exactly right for desks, consoles, benches and bar tops.
  • Short slabs. Under 220 cm the dining market thins out, and that is coffee table and desk territory.
  • Species other than walnut. Plane in particular gives length and width at a lower price: oak or plane for a table top.
  • Decorative defects in the right place. A void you were going to pay to have created, already there.

And where to be careful

A very cheap slab is cheap for a reason. Ask which one: is it wet, twisted, split through, or sapwood-heavy? Any of those can be fine for your project, and all of them should be known before you buy. The questions are in buying a slab online.

Our whole stock, with area and price per square metre for every piece, is published in the slab price index, so you can see the spread rather than take our word for it.

Common questions

Is walnut always more expensive than oak?

At comparable size and quality, usually yes in European markets, because demand for walnut is higher and large walnut is scarcer. Plane is typically cheaper than both.

Does VAT apply?

Our prices are per slab without VAT. What you pay depends on your status and country, so ask when we quote.

Why is a bookmatched pair more than two slabs?

Because the match cannot be recreated once separated, and holding both until a buyer wants the pair ties up stock. See bookmatched pairs and river tables.

Does the price include flattening?

No. Slabs are supplied rough sawn, so flattening and finishing are your maker's work. That is why the finished thickness is lower than the rough dimension.

Prices are on every slab

Per slab, without VAT, with the measurements that justify them. Shortlist what fits and we quote delivery within a day.

See slabs and prices