Bookmatched Pairs and River Tables
What bookmatched means, why pairs are priced together, and how a river table uses the two inside edges.
A bookmatched pair is two slabs cut one after the other from the same log, so that opening them out like a book gives a nearly mirrored figure. They are sold and priced together because separating them destroys the only thing that makes them worth more than two ordinary slabs.
What bookmatched actually means
When a log is cut through and through, each slab is the next layer down. Two adjacent slabs therefore show almost the same grain, knots and edge shape, because only a saw kerf of material separates them.
Flip one over and put it against the other and the figure mirrors across the joint. That is a bookmatch. Two points that catch people out:
- It is nearly mirrored, not exactly. The saw removed a few millimetres, and grain changes through that thickness. Knots shift slightly, the edge shape differs a little.
- Flipping one slab means one face of the pair is the "up" face on one and the "down" face on the other. If one slab has a defect on its good side, the bookmatch forces you to deal with it.
Why pairs are priced together
There is no second chance at a bookmatch. If one slab of a pair is sold separately, the other becomes an ordinary slab, and the value of the match is gone for everyone. That is why they carry a single price.
It also means a pair is a specific kind of purchase: you are buying a design decision, not just material. Before committing, work out what the pair is for, because the two main uses need different things from it.
Use one: a wide top from two slabs
Join the two inside edges, straight, and you get a top wider than any single slab from that tree, with a mirrored figure running away from the centre line.
What this needs:
- A straight, true join. Both inside edges jointed flat and square, which means cutting off the live edge on the inside of both slabs.
- A glue line that holds. A plain butt joint in a wide top is a long cross-grain glue line under seasonal stress. Done properly with a modern adhesive it holds; done badly it opens.
- The two slabs to behave together. Adjacent slabs from one log at the same moisture content move similarly, which is one more argument for a pair over two unrelated slabs.
The result: both live edges end up on the outside, the mirrored figure runs out from the middle, and you have a top at nearly double the width.
Use two: a river table
A river table turns the two slabs so the live edges face each other with a gap between them, and fills the gap with resin.
The appeal is obvious. The practical considerations are less so:
- The live edges are the design. You want edges with interesting shape and variation, because the resin river traces them. Two straight-ish edges make a boring river.
- Bark must come off completely. Resin against bark traps air, discolours and eventually releases. Every bit of bark down to clean wood.
- Deep pours take planning. Resin generates heat as it cures, and a deep pour in one go can overheat, yellow, crack or shrink. Casting resins for deep pours exist and have their own slow schedules.
- Resin does not move; wood does. This is the engineering truth of river tables. The wood expands and contracts across the width with the seasons, the resin does not. The bond is what absorbs the difference, and on a wide top that stress is real.
- Cost. The resin for a full-length deep river in a 260 cm table is not a small part of the budget.
None of that makes river tables a bad idea. It makes them a project with a real technique behind it rather than a weekend job.
Which pair for which job
| Pair | Suits |
|---|---|
| C18 and C19, walnut, 300 cm, 90 to 108 cm each | A very wide dining top at around 200 cm across joined, or a dramatic river table with chocolate heartwood against a dark or clear resin. |
| P-19 and P-20, plane, 260 cm, 120 to 130 cm each | An enormous low table, a wide island, or a pale river table where a coloured resin reads strongly against cream wood. |
The thing to decide before you buy
Whether the live edges go inside or outside. It changes which slab faces up, which faces get the figure, and what you do with the inside edges. Once an inside edge is jointed straight for a glue line, the river table option is gone.
Both routes need the top fixed so it can still move, which on a joined pair at nearly 200 cm wide is a lot of movement. See attaching a slab top to a base and seasonal movement and humidity.
C18 and C19, walnut, 300 cm long, 90 to 108 cm wide each, 6 cm thick. P-19 and P-20, plane, 260 cm long, 120 to 130 cm wide each, 6 cm thick. Both kiln dried to 8 to 10 percent, supplied rough sawn, priced as a pair without VAT.
Common questions
Can I buy one slab of a pair?
Ask. The pair is priced together because splitting it destroys the match, so the answer is usually no while both are available.
Does a river table need to be thicker than a normal top?
The wood does not, but the resin river is not structural in the way the wood is, so the two halves are effectively two narrower tops joined by a flexible line. Keep the supports under the wood, not under the river.
Will the resin yellow over time?
Clear epoxies vary a great deal in UV stability. If the table will sit in sunlight, choose a resin specified for UV resistance and expect some change anyway. Ask the resin manufacturer rather than the slab seller.
Is a bookmatched top more stable than a single slab?
No. It is two boards joined, so it moves as a wider panel. The advantage is width and symmetry, not stability. A single slab is simpler: one slab or a glued-up top.