Oak Bar Top for Home and Commercial Use

Oak is the usual choice for a bar that gets wet. Depth, overhang and the build-up that lasts.

Species and use5 min readUpdated 2026-10-23

Oak is what bars have been made of for a long time, and the reasons are practical rather than traditional: it is hard, it is dense, it takes a tough finish, and it is available long and straight.

Heights, depths and overhangs are the same for any species and are set out in the walnut bar top piece. This is the oak case.

Hardness on a surface that takes impacts

A bar top gets a specific kind of damage: a glass base set down hard, a bottle put down without looking, a till or a card machine slid across it. Those are point impacts, and oak resists them better than walnut or plane.

In a commercial setting this is the whole argument. A home bar sees a fraction of that traffic, so the choice is more open and more about colour.

Water, tannin and a wet bar

Oak is durable in contact with water, which is why it has been used for barrels and boats. That durability is about rot resistance over years, not about surface marks over weeks.

Two things to manage:

  • Open pores hold liquid. Spilled wine sits in the grain rather than beading off a flat surface. On a bar, this argues for either a grain-filled, fully built finish, or for a maintenance habit of wiping rather than letting things dry.
  • Tannin and iron. Steel bottle openers, a damp steel tray, a cocktail shaker base left on a worn patch. Blue black stains follow. Keep the finish intact and use stainless hardware.

Building a finish that survives a bar

This is where a bar top differs from everything else in the house, and where most home builds fail.

  1. Decide between repairable and resistant before you start. Hardwax oil is repairable and will mark. A two-part lacquer is resistant and cannot be spot-repaired. You cannot have both.
  2. Seal the underside and all edges to the same standard as the top. On a bar the underside is the face that sits over a damp cellar, a fridge or a sink, and an unsealed underside takes up moisture and cups the top.
  3. Cure fully before service. An oil that is touch dry is not cured. Putting a bar into use after three days is why bars get ring marks in week one.
  4. Plan the maintenance. On oil, the front edge and the two or three spots where drinks land need re-oiling long before the rest. Doing that strip annually keeps the whole top ahead of the damage.

Comparison in hardwax oil, lacquer or epoxy.

Commercial use: the things that change

If this is a public bar rather than a home one, three extra considerations, and none of them is about the wood:

  • Local hygiene and fire regulations may have something to say about surfaces and finishes in a food and drink setting. Check with the authority that licenses the premises rather than assuming.
  • Cleaning chemicals. Commercial sanitisers are far harsher than domestic ones and will strip an oil finish quickly. Match the finish to the cleaning regime, or the regime to the finish.
  • Downtime for refinishing. An oiled bar can be refreshed overnight. A lacquered one cannot. Factor that into the choice.

Ray fleck along a bar

A bar is viewed along its length from standing height, which is the best angle for oak's medullary rays to catch the light. The strip of a slab nearest a live edge carries the most fleck, and that is also the strip you want at the front where people look. Say so when the cutting is planned, because the alternative is cathedral grain and far less shimmer. The background is in oak dining tables.

Oak in stock

O-15 and O-16 at 300 cm long, 85 to 95 cm wide, 6 cm thick, which rip to a 45 cm bar top plus a back shelf. Kiln dried to 8 to 10 percent, supplied rough sawn. Prices per slab, without VAT.

Common questions

How long can a bar top run in one piece?

Our oak reaches 300 cm. Beyond that you are joining slabs, and the join is best placed over a support rather than in a span. Plane runs to 330 cm if length is the priority: plane bar tops.

Is epoxy the right finish for a bar?

It is the most liquid-proof and the least repairable, and it changes the surface from wood to plastic-over-wood. For a home bar it is usually overkill. For a commercial bar that cannot close for refinishing, it has a case.

Can the bar top overhang 40 cm with no support?

In 6 cm oak, usually yes for weight alone, but a bar edge takes people leaning hard on it. Add a steel plate or corbels past 30 cm and keep the fixings slotted.

Oak, 300 cm long

O-15 and O-16 are both 300 cm and rip to bar depth with a live edge on the front. Shortlist one and we come back within a day.

See the oak