Walnut Bar Top From a Long Narrow Slab
Bar heights, depth for elbows and drinks, and the finish that handles spills on a walnut top.
A bar top is a long narrow surface people stand or perch at, put wet glasses on, and lean their forearms against. It is the use that is hardest on a finish and easiest on the structure.
The three heights, and which one you want
| Height to top surface | What it is | Stool seat |
|---|---|---|
| 90 cm | Kitchen counter height. Standing work, perching on a low stool. | 60 to 65 cm |
| 105 to 110 cm | Bar height. Standing comfortably, high stools. | 75 to 80 cm |
| 75 cm | Table height. Dining chairs. Not a bar. | 45 cm |
The gap between the stool seat and the underside of the top should be 27 to 32 cm, the same relationship as a bench and a table. With a 6 cm slab at 105 cm, the underside is at 99 cm and the stool wants a 70 cm seat.
Buy the stools after the top is built, not before. Slab thickness varies and 2 cm of unexpected top thickness ruins the relationship.
Depth: narrower than people think
A bar top needs enough depth for forearms, a drink and a phone. That is 40 cm, not 70.
- 30 cm: a drinks ledge. A glass and nothing else.
- 40 to 45 cm: the standard. Elbows, a drink, a plate of small food.
- 55 to 60 cm: a full place setting, so it is a high dining table rather than a bar.
- Over 70 cm: you are standing too far from the person opposite to talk comfortably.
This is why a long narrow slab, which is awkward for a dining table, is ideal here. W-22 at 310 cm by 75 to 85 cm rips into a 45 cm bar top with a live edge on the front plus a 35 cm shelf from the remainder.
Overhang if people sit under it
If the top sits on a cabinet or a stud wall and people perch on the outside, you need 25 to 30 cm of knee overhang minimum, and 35 to 40 cm to be comfortable. A 6 cm walnut slab cantilevers that without support in most cases, but a person leaning their full weight on the outer edge is a heavier load than it appears. Past 30 cm, add a steel plate or corbels under it, with fixings that still let the top move. See attaching a slab top to a base.
The finish is the whole problem
A bar top sees more standing liquid than any other surface in a house, and the liquid is often acidic or sugary. Red wine, citrus, cola, beer.
The honest comparison for a bar:
| Finish | On a bar top |
|---|---|
| Hardwax oil | Repairable, good looking, and it will mark. Needs re-oiling at the front edge regularly. The right answer for a home bar. |
| Two-part lacquer | Genuinely resistant to spills and acid. Hard to repair, and when it fails it fails visibly. The right answer for a commercial bar. |
| Epoxy pour over the top | Bulletproof against liquid, deadens the wood's texture, scratches visibly and cannot be spot repaired. |
The full version of this argument is in hardwax oil, lacquer or epoxy.
Walnut specifically
- Dark wood hides a bar's life. Ring marks, drips and general use are far less visible on chocolate heartwood than on cream plane. This is the main argument for walnut here.
- It is soft. A bar takes glasses set down hard, bottle bases and keys. Expect dents.
- Warm under the forearms. People rest on a bar for long periods. Walnut is kinder than stone or a dense wood.
W-22 at 310 cm by 75 to 85 cm and W-21 at 280 cm by 85 to 95 cm are the closest shapes to a bar top in stock. Both 6 cm, kiln dried to 8 to 10 percent, supplied rough sawn.
Common questions
Does a bar top need a different thickness from a table?
Not structurally, because the spans are usually short. Visually, a bar reads better thick, because you see the edge straight on at standing height rather than from above. 6 cm or more.
Can I put a sink in a bar top?
Yes, with the cut edges fully sealed, including the underside lip, and the top fixed so it can still move around the fixed sink. See kitchen island tops for cut-out detail.
What about an outdoor bar?
Not with these slabs. Kiln dried interior walnut outdoors will move hard, check and grey. Outdoor timber is a different species choice and a different drying spec.