A Walnut Slab Bench for a Dining Table
Bench height, length and thickness so it tucks under the table and does not sag in the middle.
A bench is the piece people add after the table, and the piece that is easiest to buy wrong. The two failure modes are a bench that does not slide under the table and a bench that visibly bends when two adults sit on it.
Both are solved by numbers before you order.
Height, measured from the table down
Bench height is not a standard, it is a relationship. You want 27 to 32 cm of gap between the bench seat and the underside of the table top.
Work backwards:
| Step | Example |
|---|---|
| Table top height | 75 cm |
| Minus slab thickness | 6 cm, so the underside is at 69 cm |
| Minus seat gap | 30 cm, so the bench seat sits at 39 cm |
| Bench seat thickness | 5 cm, so the legs are 34 cm |
That 39 cm result is lower than a dining chair, which usually sits at 45 to 47 cm. This is why people complain that benches are uncomfortable: they are fine at 45 cm, but at 45 cm with a 6 cm table top you only have 24 cm of thigh clearance and the bench will not tuck away.
The compromise most people land on: bench seat at 42 to 44 cm, accepting that it tucks only partly under. Decide which matters more before building.
Length and the sag problem
This is where a slab bench differs from a slab table. A table is supported near its ends and loaded lightly in the middle. A bench is supported near its ends and loaded with two adults in the middle.
Rules that hold up:
- Up to 120 cm between supports: 4 cm is enough.
- 120 to 160 cm: 5 cm, and keep the overhang past each leg under 20 cm.
- Over 160 cm: 6 cm, or add a third support in the middle, or a steel flat bar let into the underside.
A 180 cm bench on two legs at the extreme ends, in 4 cm walnut, with two people in the middle, will deflect visibly and will keep deflecting. The stiffness maths is in how far a slab can span unsupported.
Benches are usually about 30 cm shorter than the table so they sit inside the legs, but match the look you want: flush with the table ends reads deliberate, shorter reads lighter.
Depth, and the edge you sit on
35 to 40 cm deep is right. Below 30 cm it is perching. Above 45 cm it becomes a seat you have to shuffle back on, and it stops tucking under the table.
The front edge is the detail that decides comfort. A square arris at the front cuts into the back of the thigh after twenty minutes. Options:
- A generous radius, 10 to 15 mm, on the front top edge. The minimum.
- A chamfer or a slight undercut, which is more comfortable still and reads as a designed detail.
- The live edge at the front, which is beautiful and must be fully rounded and sanded far smoother than any other face, because the bark side will catch clothing otherwise.
Walnut specifically
- Softer means warmer and kinder to sit on. Walnut takes the chill off faster than oak and does not feel as hard through thin clothing.
- It will record the use. Belt buckles, rivets and keys in back pockets mark a walnut seat. This is where a bench gains its character or its damage, depending on your temperament.
- Matching the table matters more than usual. If the bench comes from the same slab as the table, the colour and figure carry across and the pair reads as one object. If it comes from a different walnut slab, expect a visible difference in heartwood colour.
That last point is the strongest argument for planning the bench at the same time as the table rather than a year later. The heartwood of one walnut tree is not the heartwood of another.
A 300 cm dining slab at 110 cm wide gives a 100 cm wide table plus a 180 by 38 cm bench from the rip, with the same grain running through both. Tell us the plan before anything is cut.
Common questions
How many people fit on a bench?
About 55 to 60 cm per adult, so 120 cm seats two comfortably and 180 cm seats three. Benches seat more at a push than chairs do, which is part of their appeal.
Does a bench need the same movement allowance as a table?
Yes. A bench seat is a solid cross-grain panel like any other and has to be able to expand across its depth. Slot the fixings into the legs.
Will a walnut bench be slippery when finished?
A high-gloss film finish can be. Hardwax oil leaves enough texture that it is not an issue, which is one more reason oil is the usual choice on seating. See which finish to use.
Can I use a cookie or a very short slab as a bench?
A cookie is cut across the trunk and moves differently, so it is a stool rather than a bench. See cross-cut rounds as side tables.