A Conference Table From a Single Slab

Seating six to twelve around one piece of wood: lengths, widths, cable routing and base spacing.

Species and use6 min readUpdated 2026-10-23

A conference table is a dining table with a different brief: more people, more equipment, more hours of use, and a room where it is the only object anyone looks at. A single slab does something in a meeting room that a veneered boardroom table cannot, and it brings three specific problems with it.

How many people fit

Boardroom spacing is more generous than dining spacing, because people have laptops, papers and elbows out for an hour.

SeatsLengthWidth
Six, three a side220 to 240 cm100 to 110 cm
Eight, four a side280 to 300 cm110 to 120 cm
Ten, four a side plus ends300 to 330 cm110 to 130 cm
TwelveOver 360 cm, which means joining slabs120 to 140 cm

Allow 70 to 75 cm of edge per person, not the 60 cm used for dining. Width matters more than at a dining table too, because two people opposite each other with open laptops need 110 cm minimum before the screens meet in the middle.

Clearance around the table: 100 to 120 cm behind the chairs, because people get up and walk out during meetings far more than they do at dinner.

Problem one: base spacing with people at the ends

A dining table seats nobody at the ends in most households. A conference table does, and that person needs knee room exactly where a trestle or a pedestal base usually goes.

Three workable layouts:

  • Two end frames set well in, at 50 to 60 cm from each end. Leaves the end seats clear and keeps the span sensible.
  • A single central spine with feet, which leaves both ends and all sides open but puts a bar down the middle underfoot.
  • Four legs at the corners, which gives the longest clear span and crowds the end seats.

Whichever you choose, the overhang past each support is the number that decides whether the table feels solid when someone leans on the end. The limits are in how far a slab can span unsupported.

Problem two: cables

A slab has no apron, no modesty panel and no cavity. Everything you run has to be designed in before finishing.

  1. Decide the power and data positions first, from the room's floor boxes or wall points, then work backwards to where the table sits.
  2. Grommets or a flip-up box let into the top. Cutting a rectangular box out of a slab removes material from the middle of the span, so keep it modest and away from the centre line if possible.
  3. A cable tray underneath, fixed with slotted holes so the top can still move across its width. This is the least invasive option and the one to prefer.
  4. Seal every cut edge, including the inside of grommet holes and the box cut-out.

Problem three: it is the only object in the room

A meeting room is usually plain, so the table is doing all of the visual work and every detail is visible.

  • Defects become features or flaws depending on scale. A small void in a 330 cm top is a detail. A 60 cm crack down the middle is the table.
  • The finish gets inspected by people sitting in front of it for an hour with nothing else to look at. A rushed finish shows.
  • Wear concentrates. The seats nearest the door get used every meeting; the far end gets used quarterly. On an oiled top expect visible difference within a year, and re-oil the whole table rather than the worn strip.

Which species for a meeting room

  • Walnut reads as the expensive choice, hides marks, and suits a room with a dark floor. It dents, which in an office with laptops and phones is a real factor.
  • Oak is the hard-wearing option and the one to choose if the room is heavily used. It ambers over the years.
  • Plane gives you the longest tops at the lowest price and suits a bright, modern room. Pale wood shows coffee rings.
Long slabs in stock

W-24, walnut, 320 cm by 80 to 170 cm at 7 cm thick. P-15 and P-17, plane, both 330 cm. O-15 and O-16, oak, 300 cm. All kiln dried to 8 to 10 percent, supplied rough sawn. Prices per slab, without VAT.

Common questions

Can a conference table be made from two slabs joined?

Yes, and for anything over 330 cm it has to be. A bookmatched pair makes the join deliberate: bookmatched pairs and river tables. Put the join over a support.

How thick should a boardroom table be?

6 to 7 cm. The spans are long, the table is on show, and a thin top on a 300 cm length looks wrong even when it is structurally fine. See how thick should a slab table be.

Will a slab table work in an air-conditioned office?

Air conditioning holds humidity steadier than domestic heating does, which is good for a wide solid top. The risk is a very dry office in winter. Fix the top so it can move and read seasonal movement and humidity.

How do we get a 330 cm table into an office?

Lifts and stairwells are the constraint, not doors. Measure the route first: measuring your door and stairwell, and plan for four people.

The long slabs

W-24 at 320 cm in walnut, P-15 and P-17 at 330 cm in plane. These are the three that seat ten. We send photographs and a delivery quote within a day.

See the long slabs