Will It Fit: Measuring Doors and Stairs

The measurements to take before you order a three-metre top, including the turn at the top of the stairs.

Delivery in Europe5 min readUpdated 2026-10-23

A three metre slab will go through a standard door. It will not go round a standard landing. The constraint is almost never the door width, it is the turning room on the far side of it, and that is the measurement nobody takes.

What actually stops a slab

A slab is long, wide and rigid. It can be tipped onto its edge, which makes the width irrelevant and the length and thickness the limits. So at each obstacle the real question is: with the slab on edge, is there room to swing the far end round?

Four places go wrong, in order of how often:

  1. The turn at the top or bottom of a staircase. You need roughly the slab length as diagonal room at the turn.
  2. A hallway corner. Same problem on the flat.
  3. A door at the end of a short hall. The slab goes through the door but cannot be rotated to line up with it.
  4. The last metre. Getting a 110 kg slab past a radiator and a doorframe without damaging either.

The measurements to take

Write them down and send them with your enquiry. Ten minutes now is worth a great deal later.

MeasureWhy
Every door width and height on the routeSlab on edge needs the height, flat needs the width
Hallway width at every cornerCorners are where the turn happens
Diagonal across each landingThis is the real staircase constraint
Stair width and ceiling height above the stairsYou may need to tilt as well as turn
Lift car dimensions, including the diagonalA 240 cm slab will not go in most residential lifts
Where the lorry stops to the front doorCarrying distance, and whether it is uphill

The corner rule

To get a slab round a right-angle corner between two corridors, you need the two corridor widths to satisfy roughly this: added together they should comfortably exceed the slab length, with a margin.

A 300 cm slab turning from a 120 cm hall into a 100 cm hall has 220 cm of combined width against a 300 cm slab. That will not go on the flat. It may go if you can tilt it diagonally and the ceiling is high enough, which is why ceiling height is on the list.

Test it for free

Cut a strip of cardboard or a length of batten to the slab's exact length and walk the route with it. If the batten goes, the slab goes. This takes fifteen minutes and has saved a lot of returned pallets.

When the route does not work

There are more options than people assume.

  • Through a window or balcony door. Common in city flats. Needs the window to open fully and enough people.
  • Take a door off its hinges. Gains 3 to 5 cm and sometimes gains the few degrees of swing that matter more.
  • Finish it in the room. If the slab fits in rough but the finished table will not come apart, assemble and finish in place. This is normal for large tables.
  • Choose a shorter slab. The honest option. A 240 cm table that fits beats a 300 cm table in the garage.
  • Have it cut to length before shipping. If you know the finished length, tell us. The slab still needs trimming for the end checks anyway. See what size slab seats six people for how to arrive at the number.

Weight on stairs

Stairs change the arithmetic. Carrying 110 kg along a hall is three people. Carrying it up a turning staircase is four, with one person able to see where they are going, and a plan for what happens if somebody needs to stop.

Two practical points: the person at the bottom carries more than the person at the top on an incline, and the slab should go up on edge, not flat, because on edge it is stiff and people can get a hand under it. See carrying and lifting a slab safely.

Protect the route first

Before anything moves: corner protectors on doorframes, something over the floor, and take pictures off the walls along the route. A slab does not stop for a light switch.

Common questions

Will a 3 metre table fit through a standard door?

The door itself is rarely the problem. Tipped on edge, a slab passes through a standard doorway. The constraint is the turning room on either side of the door, especially at a staircase landing or a hall corner.

How do I check whether a slab will fit up my stairs?

Cut a batten or a cardboard strip to the slab length and carry it along the route. If the batten turns every corner, the slab will. Measure the landing diagonal and the ceiling height above the stairs as well.

Can a slab go in a lift?

Rarely in a residential lift. Measure the car's internal diagonal, including corner to opposite corner at an angle, and compare it to the slab length before counting on it.

Can you cut the slab shorter before sending it?

Tell us the finished length you need and we will discuss it. The ends usually need trimming past the drying checks in any case, so cutting before shipping often loses nothing.

Send us the route, not just the address

Door widths, corner measurements and where a lorry can stop. We will tell you which slabs reach the room and quote the delivery within a day.

Start a shortlist