How Thick Should a Slab Table Be

Why 5, 6 and 7 cm are the common thicknesses, how thickness interacts with span, and when thicker is only heavier.

Choosing a slab6 min readUpdated 2026-10-23

Thickness is the specification people worry about least and regret most. Too thin and a long top sags or feels flimsy at the edge. Too thick and you have paid for weight, lost knee room and made delivery harder, with no improvement in the table.

The slabs we carry are 5, 6 or 7 cm rough sawn. Here is what each is for.

The short version

Finished thicknessWhere it belongs
3 to 4 cmShelves, small consoles, coffee tables, bench seats under 150 cm
4.5 to 5.5 cmDesks, consoles, coffee tables, dining tables up to about 220 cm
5.5 to 6.5 cmThe standard dining table. Right for almost everything from 200 to 320 cm
6.5 to 8 cmVery long or very wide tops, bars, conference tables, anything that wants mass

Note those are finished figures. A rough-sawn slab loses 3 to 6 mm to flattening both faces, sometimes a centimetre if it has a twist to take out. A 6 cm rough slab usually finishes between 5.4 and 5.7 cm.

Why thickness matters more than it looks

Stiffness in a flat panel does not scale with thickness, it scales roughly with thickness cubed. Double the thickness and you get around eight times the resistance to bending.

That has a useful consequence: the difference between 5 cm and 6 cm is not 20 percent, it is closer to 70 percent more stiffness. Going from 6 cm to 7 cm adds about another 60 percent. Small changes in thickness buy a lot of performance, which is why a 6 cm top handles a 3 metre length without drama.

It also means the reverse. A 4 cm top is not slightly less stiff than a 6 cm top, it is less than a third as stiff. On a long table that is the difference between flat and visibly bowed between the legs over a few years.

Thickness and span go together

The real question is never thickness alone, it is thickness against the distance between supports. A 5 cm top on a base set 120 cm apart is stiffer in practice than a 7 cm top on a base set 240 cm apart.

As a working rule for a dining top, keep the overhang past each base no more than about 40 cm at 5 cm thick, 45 to 50 cm at 6 cm, and 55 cm at 7 cm. Those are not limits where the wood fails, they are limits where the end of the table stops feeling solid when somebody leans on it. The full treatment is in how far a slab can span unsupported.

What thickness does to the look

The visible edge of a table is a strong part of its character, and the live edge exaggerates it. A 7 cm walnut slab with bark texture down both sides reads as a piece of tree. A 4 cm version of the same slab reads as a table.

Two things to hold in mind:

  • Longer tops need more thickness to look right. A 320 cm top at 5 cm looks thin even if it is structurally fine. Proportion is doing work here, not physics.
  • You can cheat the look downward but not upward. Chamfering or undercutting the bottom of the edge makes a thick top look lighter. Nothing makes a thin top look thick.

Where thicker stops helping

Past about 7 cm on a dining table you are adding problems:

  • Weight. Thickness is directly proportional to weight. Going from 6 to 8 cm on a 300 by 100 cm walnut slab adds roughly 38 kg to something already near 120 kg. See working out what a slab weighs.
  • Knee room. The underside of the top sets how high your thighs have to be. A thick top on a standard 73 cm base eats clearance, and anyone at the end of the table meets the slab with their knees.
  • Drying history. Thicker stock dries more slowly and is more likely to hold a moisture gradient between its core and its faces. That is one reason to care about moisture content on thick slabs specifically.
  • Cost. You are buying volume. Thickness is the most expensive dimension per unit of visual effect.
Rule of thumb

For a dining table: 6 cm unless you have a specific reason. Go to 7 cm past about 280 cm long, or when the base has to sit well inboard of the ends. Drop to 5 cm only for desks, consoles and coffee tables.

Bars, islands and desks

A bar top wants thickness for the same reason a dining table does, plus one more: the front edge takes constant weight from people leaning on it. 6 to 7 cm, and support the back edge continuously.

A kitchen island top normally sits on cabinets, which means continuous support and almost no span. 5 cm is plenty structurally. People still go to 6 cm for the overhang where stools tuck under.

A desk at 5 cm looks and behaves well, and it keeps the weight low enough for one person to lift onto a base. At 7 cm a desk starts to feel like a workbench, which may be the point.

Common questions

Is 5 cm thick enough for a dining table?

Yes up to about 220 cm long, provided the base is not set far inboard. Beyond that, 6 cm is the safer choice for both stiffness and proportion.

How much thickness is lost when a slab is flattened?

Typically 3 to 6 mm across both faces. A slab with a cup or twist can lose a centimetre or more, because flattening has to cut down to the lowest point of the high face.

Does a thicker slab crack less?

No. Thickness does not prevent movement, and thick stock can carry a bigger moisture difference between core and surface. Stable behaviour comes from correct drying and a fixing method that allows movement, not from mass.

Can I make a thick slab look thinner?

Yes, by chamfering or undercutting the underside of the edge so the visible face is shallower than the actual top. It is a common trick on heavy tops and it does not weaken anything if you leave the main body intact.

Every slab lists length, width and thickness

Filter the stock, shortlist what suits your span, and we send photographs, exact measurements and a delivery quote within a day.

See slabs in stock