Working Out What a Slab Weighs

Volume times density, with the density ranges for walnut, oak and plane, so you know before you book help.

Bases and engineering5 min readUpdated 2026-10-23

People underestimate slab weight by a factor of two, consistently. A table top that two people carried in a photograph is usually four people and a plan. Work it out before the pallet arrives, not when the driver is waiting.

The calculation

Weight is volume multiplied by density.

Volume in cubic metres = length (m) x width (m) x thickness (m). For a live-edge slab, use the average width, not the widest point.

Density depends on species and on how dry the wood is. At the 8 to 10 percent moisture content our slabs are dried to, these ranges are a reasonable working basis:

SpeciesApproximate density
Walnut620 to 680 kg per cubic metre
Plane (lacewood)600 to 660 kg per cubic metre
Oak700 to 760 kg per cubic metre

Individual boards vary, so take the middle of the range for planning and the top of it when you are deciding how many people to ask.

Worked examples

Walnut dining top, 300 x 95 x 6 cm.
3.0 x 0.95 x 0.06 = 0.171 cubic metres.
0.171 x 650 = about 111 kg.

Oak island top, 300 x 88 x 6 cm.
3.0 x 0.88 x 0.06 = 0.158 cubic metres.
0.158 x 730 = about 116 kg.

Plane desk, 240 x 120 x 5 cm.
2.4 x 1.20 x 0.05 = 0.144 cubic metres.
0.144 x 630 = about 91 kg.

Walnut coffee table, 110 x 95 x 7 cm.
1.1 x 0.95 x 0.07 = 0.073 cubic metres.
0.073 x 650 = about 48 kg.

Note how fast thickness moves the number. The same walnut dining top at 8 cm instead of 6 cm goes from 111 kg to about 148 kg, which is the difference between an awkward lift and a job needing equipment.

Quick mental version

For a 6 cm hardwood slab, every square metre of face area weighs roughly 40 kg. A 3 metre by 1 metre top is about 3 square metres, so about 120 kg. Good enough to plan with.

What the number means in practice

WeightWhat it takes
Up to 40 kgOne strong person, awkwardly. Two is better
40 to 80 kgTwo people, planned route, no stairs if avoidable
80 to 130 kgThree or four people, or two with lifting straps and a clear path
Over 130 kgFour people minimum, or a trolley and a ramp. Think about stairs seriously

The weight is not the hard part. A slab is heavy and three metres long, so most of the difficulty is leverage and corners. How to actually carry one is in carrying and lifting a slab safely.

Add the packaging

A slab arrives on a pallet with protection around it. For planning a delivery, add roughly 15 to 25 kg for the pallet and packaging. That is the figure the carrier is working to, and it is why a pallet is a tail-lift delivery rather than a van drop. See how a slab ships across Europe.

Weight after finishing

A finished top is slightly lighter than the slab you received, because flattening removes material. Taking 5 mm off a 6 cm slab removes about 8 percent of the volume. A 111 kg slab becomes roughly 102 kg finished, before the base.

It also gets a little heavier again if you do a deep resin pour, since cured epoxy is denser than the wood it replaces. For normal void filling this is a kilogram or two and not worth calculating.

Does the floor care

Usually not. A 130 kg table spread over a base footprint is a modest load for any sound floor. It is worth a thought on an old timber floor with a very concentrated pedestal base, where the load lands on a small area. See floor loading and very heavy tables.

Common questions

How much does a wood slab table top weigh?

Multiply length by average width by thickness in metres, then by the species density. For a 6 cm hardwood slab a useful shortcut is about 40 kg per square metre of face area, so a 3 by 1 metre top is around 120 kg.

Is oak heavier than walnut?

Yes. European oak runs roughly 700 to 760 kg per cubic metre against 620 to 680 for walnut, so the same slab in oak is around 10 to 15 percent heavier.

How many people do I need to carry a slab?

Two up to about 80 kg with a clear route, three or four above that. Length matters as much as weight: a three metre slab needs people at the ends regardless of what the scales say.

Does moisture content change the weight?

Yes, a little. Water is part of the weight, so a slab at 12 percent is a few percent heavier than the same slab at 8 percent. For planning a lift it is not a significant difference.

Every slab lists its dimensions

Length, both widths and thickness are on each piece, so you can run the numbers before you commit. We include the weight on the delivery quote.

See slabs in stock