Base Height for Dining, Desk and Bar

Finished heights that work, and how to subtract the slab thickness so the base you order is right.

Bases and engineering4 min readUpdated 2026-10-23

You order a base in a height and you receive a table in a different height, because the slab adds its own thickness on top. Getting this wrong by a centimetre or two is the single most common ordering mistake, and it cannot be fixed afterwards.

The arithmetic

Base height = finished height you want minus the actual measured thickness of your slab.

Measure the slab rather than trusting the listing, and measure it after flattening, because a router sled takes a few millimetres off. A slab listed at 6 cm can finish at 5.5 cm after flattening, and a base ordered at 74 minus 6 then gives you a 73.5 cm table.

Finished heights that work

UseFinished top heightSeat height it suits
Dining table74 to 76 cm45 to 47 cm chair
Desk, fixed73 to 75 cmAdjustable office chair
Kitchen counter height90 to 92 cm60 to 65 cm counter stool
Bar height105 to 110 cm75 to 80 cm bar stool
Coffee table40 to 45 cmSofa seat height, roughly level
Console75 to 90 cmNot for sitting
Hallway bench45 to 47 cmSame as a dining chair
Bathroom vanity80 to 85 cmTaller than old standards, measure the basin
The gap is what matters, not the height

What decides comfort is the distance between the seat and the underside of the table, not the table height itself. For dining, aim for 25 to 30 cm of clear leg gap. Measure from the chair seat to the underside of the slab, including any apron or rail, because that is where knees actually meet the table.

The clearance trap

A 74 cm table with a 6 cm slab has its underside at 68 cm. A chair with a 46 cm seat leaves 22 cm of leg gap, which is tight. Thick slabs eat clearance, and a base rail under the slab eats more.

Two fixes: raise the finished height slightly for a thick top, or choose a base whose rails sit outboard rather than directly under the knees. Base shapes are compared in steel base shapes for a slab top.

Measure the chairs you own

Chair seat heights vary more than table heights do. Measure the chairs you intend to use before ordering anything, and if they are 42 cm rather than 46 cm, drop the table proportionally. A table matched to the chairs beats a table matched to a standard.

Counter and bar heights

These are the two where mistakes are most common, because the names are used loosely by furniture sellers.

  • Counter height is kitchen worktop height, usually 90 to 92 cm, and takes a stool with a seat around 60 to 65 cm.
  • Bar height is 105 to 110 cm and takes a stool with a seat around 75 to 80 cm.
  • A stool bought for the wrong one is useless. Decide the table height first, then buy stools.

For an island specifically, match the slab top to the existing worktop height so the two read as one surface. Detail in building a kitchen island top.

Desks

A fixed desk at 73 to 75 cm suits most adults with an adjustable chair. If the user is much taller or shorter than average and the chair does not adjust, measure instead: sitting with feet flat and upper arms vertical, the desk surface should be at elbow height.

A thick slab on a desk reduces thigh clearance, which matters more than on a dining table because you are there for hours. See walnut desk slab for the thickness trade-off.

Ordering the base

  1. Decide the finished height from the table above, adjusted for your chairs.
  2. Flatten the slab, or ask your maker what it will finish at.
  3. Measure the actual thickness in several places and take the largest.
  4. Subtract. That is the base height to order.
  5. Check whether the quoted base height includes adjustable feet at their shortest or mid setting, because that is another centimetre of difference.

Common questions

What height should a dining table be?

74 to 76 cm finished, which suits chairs with a seat height of 45 to 47 cm. Measure your own chairs, because seat heights vary more than table heights.

How do I work out the base height for a slab top?

Take the finished height you want and subtract the actual measured thickness of the slab after flattening. Check whether the quoted base height includes the adjustable feet.

What is the difference between counter height and bar height?

Counter height is around 90 to 92 cm and takes stools with a 60 to 65 cm seat. Bar height is 105 to 110 cm and takes stools with a 75 to 80 cm seat.

How much leg room should there be under a table?

25 to 30 cm between the chair seat and the underside of the top. A thick slab and a rail beneath it both reduce this.

Every slab here is the only one of its kind

Walnut, oak and plane, up to 330 cm, kiln dried to 8 to 10 percent. Shortlist what fits and we send photos, measurements and a delivery quote within a day.

See slabs in stock