Building a Kitchen Island Top

Cutting to a cabinet run, sealing the sink side, overhang for stools and sequencing around a fitted kitchen.

Build guides4 min readUpdated 2026-10-23

An island top is the slab project with the least room for error. Everything else is a piece of furniture; this one has to meet cabinets, take a sink, survive water, and be fitted around trades who are already booked.

Get the sequence right

This is the part people get wrong, and it cannot be undone.

  1. Cabinets fitted and levelled first. Everything is measured off them.
  2. Template the top from the installed cabinets, not from a drawing. Walls are not square and cabinet runs are not straight.
  3. Acclimatise the slab in the house for at least two weeks, ideally longer. A kitchen is a humid room in a dry house.
  4. Flatten, cut to size, cut the openings.
  5. Finish everything, including every cut edge, before fitting. This is the step that gets skipped.
  6. Fit the top with fasteners that allow movement.
  7. Fit sink and taps, sealing against finished wood.
  8. Final coat on the exposed surface.
The sink cut-out is where wooden worktops die

Not the surface, not the edges: the inside edge of the opening, underneath, where nobody can see and nobody finished. It is end grain, it is permanently near water, and once the sink is in you cannot reach it. Seal it to the point of saturation while the top is on trestles, with four or more coats.

Overhang for stools

If people sit at the island, the overhang is knee room.

Worktop heightOverhangSupport needed beyond
90 to 92 cm, counter25 to 30 cmOver 30 cm
105 to 110 cm, bar30 cm or moreOver 35 cm

Beyond those figures the overhang is a cantilever people lean on daily, and it wants a corbel, a steel flat bar recessed into the underside, or a leg. Detail in how much overhang a slab top needs.

Allow about 60 cm of width per stool and check the stool height matches the worktop height, which is in base height for dining, desk and bar.

Fixing to cabinets

A wooden top screwed tight to a cabinet run will crack. The top must be able to change width.

  • Slotted holes through the cabinet rails, running across the width of the slab.
  • One rigid point, usually near the centre of the run.
  • Do not over-tighten.
  • Leave a gap at any wall, 3 to 5 mm, covered by a scribe or sealant rather than butted tight.

The methods are in Z clips, figure-eight fasteners and slotted holes.

Sinks and hobs

  • Undermount sinks look best with a solid top and expose the most end grain. Seal exhaustively and expect to re-seal around them.
  • Inset sinks with a rim are more forgiving, because the rim covers the vulnerable edge.
  • Hobs need the clearance the manufacturer specifies to combustible materials, which is not a detail to improvise. Read the installation sheet before cutting.
  • Radius the corners of every cut-out generously. A square internal corner is a stress concentration and a crack waiting to start.

Finish

A hardwax oil from the manufacturer's worktop range, with the coat counts and maintenance interval in oiling a kitchen island top. If nobody will maintain it, a two-part lacquer is the honest alternative, with the trade-offs in hardwax oil, lacquer or epoxy.

Choosing the slab

An island wants width more than most pieces, and the widest slabs are the shorter ones. Our O-17 oak runs 200 cm long and up to 140 cm wide, which is an island shape rather than a dining table shape. Species considerations are in oak kitchen island top.

Common questions

Can you use a wood slab as a kitchen island top?

Yes. Seal every cut edge before fitting, fix it so it can still move across its width, and use a hardwax oil from the manufacturer's worktop range.

How much overhang for island stools?

25 to 30 cm at counter height and 30 cm or more at bar height, with support such as a corbel or a steel bar beyond that.

Should I finish the worktop before or after fitting?

Before, including the inside edges of the sink and hob openings, which cannot be reached once fitted. Apply a final coat to the surface afterwards.

How do you fix a solid wood worktop to cabinets?

Through slotted holes in the cabinet rails running across the width, with one rigid fixing near the centre. Screwing it down tight will crack it.

Every slab here is the only one of its kind

Walnut, oak and plane, up to 330 cm, kiln dried to 8 to 10 percent. Shortlist what fits and we send photos, measurements and a delivery quote within a day.

See slabs in stock