How Much Overhang a Slab Top Needs

Overhang at the ends and sides for chairs, stools and knees, and the point where it becomes a lever.

Bases and engineering4 min readUpdated 2026-10-23

Overhang is the gap between the edge of the top and the base beneath it. Too little and chairs fight the frame. Too much and the end of the table flexes when someone leans on it. The two limits are set by different things and both have numbers.

Side overhang: how far chairs tuck in

At the sides, the overhang decides whether a chair can be pushed under the table.

Side overhangResult
Under 10 cmChairs hit the frame before they are under the top
10 to 20 cmNormal range for a dining table
20 to 30 cmGenerous, good where chairs have arms
Over 30 cmTable starts to look like a shelf on a small base

On a live-edge slab the side overhang varies along the length, because the edges are not straight. Measure at the narrowest point and make sure that still works.

End overhang: the cantilever

At the ends, overhang does two jobs. It gives the end seats somewhere to put their knees, and it is a cantilever that flexes when loaded.

Finished thicknessComfortable end overhangHard limit
4 cm30 cm40 cm
5 cm40 cm50 cm
6 cm45 to 50 cm60 cm
7 cm55 cm70 cm

These are about feel rather than failure. At the hard limit the slab will not break. It will deflect enough that someone leaning on the corner notices the table move, and the fixings take a repeated load they were not designed for.

Someone will sit on the end

Design the end overhang for a person perching on it, not for a plate. At a party, somebody always does. A 6 cm slab with a 45 cm overhang takes that without complaint. The same slab with a 70 cm overhang does not.

The competing requirement

End seats want the base set back so their knees clear it. The cantilever wants the base set forward so the end does not flex. For a six seat dining table on a 6 cm slab, a base set 40 to 50 cm in from each end satisfies both, which is why that number keeps appearing. The underlying span reasoning is in unsupported span and thickness.

Counters and bars

Where people sit at stools facing the edge, the overhang is knee room and nothing else, so it needs to be bigger.

  • Counter height, 90 to 92 cm: 25 to 30 cm of overhang for comfortable knees.
  • Bar height, 105 to 110 cm: 30 cm or more.
  • Anything over about 30 cm of unsupported overhang on a counter wants support: a corbel, a steel flat bar let into the underside, or a leg. A kitchen island overhang is a cantilever people lean on daily.

Detail in building a kitchen island top and building a bar top.

Supporting a long overhang

If the design needs more overhang than the thickness allows, add stiffness rather than accepting the flex.

  • Steel flat bar recessed into the underside, running the length, fixed with slotted holes so the top can still move.
  • A corbel or bracket from a cabinet or wall.
  • A leg, which is honest and often looks better than a hidden fudge.
  • A thicker slab, which is the cleanest answer and should be decided at purchase. See the slab thickness guide.

Remember the fixings

A long overhang levers against the fixing points at the base. Make sure the fixings are strong in that direction and still allow the top to move across its width, which is the balance set out in Z clips, figure-eight fasteners and slotted holes.

Common questions

How much should a table top overhang the base?

10 to 20 cm at the sides so chairs tuck in, and 40 to 50 cm at the ends for a 6 cm slab, which balances knee room against flex.

How much overhang does a breakfast bar need?

25 to 30 cm at counter height and 30 cm or more at bar height. Beyond about 30 cm unsupported, add a corbel, a steel bar in the underside, or a leg.

Will a long overhang break the table?

It is far more likely to flex noticeably and to fatigue the fixings than to break. The limits are about how solid the table feels when someone leans on the end.

Does overhang change on a live-edge top?

Yes, because the edges are not straight. Measure at the narrowest point and make sure the chairs still clear there.

Every slab here is the only one of its kind

Walnut, oak and plane, up to 330 cm, kiln dried to 8 to 10 percent. Shortlist what fits and we send photos, measurements and a delivery quote within a day.

See slabs in stock