Building a Bar Top

Depth, bullnose or live edge at the front, drink-proofing and fixing to a stud wall or a counter.

Build guides4 min readUpdated 2026-10-23

A bar top is the one slab project where the finish decision is made for you. Everything else here is geometry; the finish is a film, because nobody is re-oiling a bar on a Tuesday.

Dimensions

DomesticCommercial
Height105 to 110 cm105 to 110 cm
Depth, drinking side only30 to 40 cm40 to 45 cm
Depth, with service behind50 to 60 cm60 cm and up
Width per stool60 cm60 cm
Knee overhang30 cm minimum30 cm minimum
Thickness4 cm and up5 cm and up

Stool height follows: a 105 to 110 cm bar takes a stool with a seat around 75 to 80 cm. Numbers in base height for dining, desk and bar.

Elbows live on the front edge

More than any other piece, a bar top is touched at its front edge, constantly, by bare forearms. That edge has to be comfortable, which on a live edge means genuinely softened rather than merely sealed, and clean, because it is at the height where dust and spills collect.

Live edge or straight front

  • Live edge at the front is the point of using a slab, and it needs the most preparation of any edge in this guide: brushed, picked clean, high points knocked back, the top arris eased. See finishing the live edge itself.
  • Straight with a bullnose is more comfortable and easier to wipe, and loses what makes it a slab.
  • Live edge at the back is a compromise worth considering: the drama faces into the room, the drinking edge is smooth.

The finish

A bar sees standing drinks, condensation, citrus, alcohol and wiping, continuously. A hardwax oil can do a domestic bar if someone maintains it. For anything commercial or busy, use a two-part lacquer or an epoxy coating. The full comparison is in hardwax oil, lacquer or epoxy.

  • Seal all six faces, including inside any hole you cut for a tap or a cable.
  • Epoxy coating gives the poured glass look and is heat sensitive, so a hot glass out of a dishwasher can mark it. Method notes in filling voids and knots with resin.
  • Matte lacquer looks far more like wood than a gloss epoxy and is the sensible middle.

Fixing it

A bar top is usually fixed to a stud wall, a counter frame or a cabinet run, which is the same engineering as an island.

  • Slotted holes through the frame so the top can move.
  • One rigid fixing near the centre of the width.
  • Into studs, not plasterboard, if any part is wall supported. Wall fixing detail in wall mounting a slab shelf.
  • Support any overhang over 30 cm with a corbel or a steel bar recessed into the underside, as set out in how much overhang a slab top needs.

Footrail

A bar at 105 to 110 cm is high enough that feet dangle. A footrail at 20 to 25 cm off the floor makes a bar comfortable to sit at for an hour instead of ten minutes, and it is the detail most home bars leave out.

Which slab

A bar wants length more than width, which suits the long plane slabs. P-15 and P-17 both run 330 cm, the longest we stock. Plane is pale, which shows red wine and hides crumbs; the trade-off is set out in plane bar top slab.

Common questions

What height should a bar top be?

105 to 110 cm, which suits stools with a seat height of 75 to 80 cm. Counter height is lower, around 90 to 92 cm.

How deep does a bar top need to be?

30 to 40 cm if people only drink at it, 50 to 60 cm if there is service behind. Allow 30 cm of knee overhang and 60 cm of width per stool.

What finish for a bar top?

A two-part lacquer or an epoxy coating for anything busy, because an oiled top needs maintenance nobody will do on a bar. Matte lacquer looks most like wood.

Should the live edge face the drinkers?

It can, and that edge then needs more softening than any other in the guide because forearms rest on it. Putting the live edge at the back is a reasonable compromise.

Every slab here is the only one of its kind

Walnut, oak and plane, up to 330 cm, kiln dried to 8 to 10 percent. Shortlist what fits and we send photos, measurements and a delivery quote within a day.

See slabs in stock