Building a Console Table
Narrow tops need different fixing. How to keep a shallow console stable against a wall.
A console is a narrow top on a narrow base, which means it is the slab piece most likely to tip. Everything about building one is about resisting a push from the front.
Dimensions
| Figure | Why | |
|---|---|---|
| Height | 75 to 90 cm | Match a nearby surface, or hall table height |
| Depth | 25 to 40 cm | Below 25 cm nothing sits on it; above 40 cm it blocks a hall |
| Length | 100 to 180 cm | Often set by the wall |
| Thickness | 3 cm and up | No span problem at these depths |
A 30 cm deep console is 90 cm tall and stands on a 30 cm footprint. Lean on the front edge and the whole thing wants to rotate forward. This is the engineering problem of a console and it has three solutions: a wider foot, mass low down, or fixing it to the wall.
Three ways to stop it tipping
- Fix it to the wall. The honest answer. A French cleat or a pair of brackets into masonry or studs, hidden behind the top. Nothing shows, and the piece becomes immovable in the direction that matters. See fixing a top with nothing showing.
- Widen the base at the floor. An A frame whose feet splay forward, or a base with a front-to-back foot deeper than the top. Changes the look.
- Put weight low. A lower shelf with books on it drops the centre of gravity considerably. The traditional solution and often the prettiest.
Two out of three is comfortable. One alone is marginal on a tall narrow piece.
Fixing a narrow top
A narrow top moves less in absolute terms, perhaps 2 to 3 mm across a 30 cm console, and that is still enough to matter. At this width, figure-eight fasteners have enough travel and are the tidiest option. See Z clips, figure-eight fasteners and slotted holes.
Never glue a narrow top to a base. It is exactly the width where people assume the movement is too small to bother with, and it is not.
Working with one live edge
Most consoles use one live edge at the front and a straight cut at the back so the piece sits against a wall. That cut is a choice: you are discarding one of the two natural edges.
- Choose the better edge for the front. Look at both under good light before cutting.
- Keep the offcut. A long thin strip of live-edge walnut has uses, and it is your finish test piece.
- Leave a gap at the wall of a few millimetres rather than scribing tight, so the top can move and air can circulate.
Where a console actually goes
Hallways, behind sofas, under televisions, in dining rooms as a serving surface. Each sets the height:
- Behind a sofa: level with or just below the back of the sofa, usually 75 to 80 cm.
- Hallway: 80 to 90 cm, where keys and post land.
- Serving in a dining room: 90 cm, counter height, so plates are easy to reach.
- Under a wall-mounted television: low enough that the kit clears, often 60 to 70 cm.
Which slab
A console is the best use for a slab that is too narrow for a table, and those are the cheaper pieces. C13 walnut at 210 cm and 60 to 80 cm wide rips neatly into a console and a shelf. Species notes in walnut console table slab and oak console table slab.
Finish
A console takes less abuse than any other piece here. Two coats of hardwax oil is plenty, and the live edge gets the usual extra attention, covered in finishing the live edge itself. A console in a hallway near a radiator is the one risk: dry heat at close range, discussed in underfloor heating and a solid wood top.
Common questions
How deep should a console table be?
25 to 40 cm. Below 25 cm nothing useful sits on it, and above 40 cm it starts to obstruct a hallway.
How do I stop a console table tipping forward?
Fix it to the wall with a French cleat or brackets, widen the base at the floor, or add a low shelf and put weight on it. Two of those three is comfortable.
Do I need movement fixings on a narrow top?
Yes. A 30 cm top still moves 2 to 3 mm seasonally, which is enough to split it if it is glued or screwed rigidly at both ends.
What height should a console behind a sofa be?
Level with or just below the back of the sofa, usually 75 to 80 cm.