Oak Console Table From a Narrow Slab
Hallway and behind-sofa consoles in oak: dimensions, weight and how to fix a narrow top so it stays put.
Oak is the console species for a hallway that takes real traffic. A console gets knocked by bags, scraped by coat zips and leaned on by everyone who sits down to put shoes on. Oak absorbs that in a way walnut does not.
The sizing is the same as any console: 30 to 45 cm deep, 80 to 90 cm tall in a hall, matched to the sofa back behind a sofa. The walnut console piece covers that ground. This is what changes with oak.
Weight, on a small footprint
Oak is denser than walnut, and a console concentrates that weight on a base with a small floor area. Two consequences people meet in practice:
- Floor marking. A heavy top on four narrow legs puts real pressure per square centimetre. On a soft floor, engineered oak or vinyl especially, that leaves dents. Use wide feet or pads.
- It is a two person lift even though it looks small. A 140 by 40 by 5 cm oak top is manageable; the same with a steel base attached is not. Work it out with what a slab weighs.
Tannin in a hallway is a real risk
Hallways are where wet things come in. Umbrellas, bike locks, keys, a dripping coat with a steel zip. Oak's tannin reacts with iron and water to leave blue black stains.
On a finished top this is mostly prevented, but two situations beat the finish:
- A wet steel object left sitting overnight on an oiled top, where water slowly penetrates a worn area.
- A bare or lightly sealed edge or underside, which is where most people skimp.
Seal all six faces, keep the finish maintained at the front edge where hands land, and put a tray down for keys. If a mark appears, oxalic acid lifts tannin stains that sanding cannot reach.
Ray fleck on a narrow piece
Oak's medullary rays show strongest where the cut runs close to radial, which on a through-sawn slab is near the two live edges. A console uses a narrow strip of a slab, so which strip you take decides how figured the finished piece is.
- Take the strip nearest a live edge and you get strong silver fleck down the length.
- Take the strip through the middle and you get cathedral arches and very little fleck.
On a 300 cm slab ripped into two consoles, those two consoles will not look the same. If they are going in the same room, say so before the cut is planned. The background is in oak dining tables, where the same effect runs across a whole top.
Fixing a narrow oak top down
A console top is narrow, so the seasonal movement across it is small, which lulls people into bolting it rigid. Do not. The movement is small but the top is also small, and a cross-grain constraint on a narrow board splits it just as readily as on a wide one.
- Figure-eight fasteners or Z-clips at the back and front, letting the top slide across its depth.
- If you are using a steel base with a flat plate, slot the holes across the grain direction and use a washer under a pan head screw.
- One fixing can be tight, to locate the top. The rest must be free to move.
Details in attaching a slab top to a base.
Where oak consoles earn their keep
- Boot rooms and side entrances, where the piece gets wet and knocked.
- Behind a sofa in a busy room, where drinks get put down without coasters.
- Under a radiator, which is harder on wood than most people realise. See seasonal movement and humidity before placing a top there, because a radiator below a narrow top dries its underside faster than its face and cups it.
O-15 and O-16 are both 300 cm long and 85 to 95 cm wide, 6 cm thick, which rip neatly into console widths. O-17 is 200 cm and 120 to 140 cm wide. All kiln dried to 8 to 10 percent, supplied rough sawn.
Common questions
Can an oak console be wall-hung with no legs?
Only into masonry or a stud, with brackets rated for the load, and calculate the cantilever properly. A 40 cm deep oak top with someone leaning on the front edge applies far more force at the wall than the weight alone suggests.
Why is my new oak console lighter in colour than the sample?
Probably time. Oak ambers with light exposure, so the sample has aged and the new piece has not. It will catch up over a year or two of daylight.
Can I make two matching consoles from one slab?
Two consoles, yes. Matching, not exactly, because the figure changes across the width of a slab. Ask for them to be cut from adjacent strips and they will be close.