Fixing a Top With Nothing Showing

Threaded inserts, blind fixings and cleats that leave the underside clean and still allow movement.

Bases and engineering4 min readUpdated 2026-10-23

On a slab table the underside is visible from a chair, from the floor and from across the room when the light is low. Fixings that work are not the same as fixings that look good, and you can have both with a little more work.

Start from the constraint

Whatever is invisible still has to let the top move across its width. Nothing in this article changes that. Hidden rigid fixings split tops exactly as well as visible rigid ones do, as described in a new crack has appeared: what now.

Threaded inserts

A metal insert is set into a bored hole in the underside of the slab, and a machine screw passes up through the base into it.

  • Why it is tidy: nothing shows except the head of a machine screw inside the base frame, usually hidden by the frame itself.
  • How to allow movement: the slots are in the steel base, not in the wood. The insert is a fixed point and the base slides relative to it.
  • Depth: a 6 cm slab takes an insert comfortably. Bore to a marked depth with a stop and never through.
  • Type: inserts designed for hardwood, driven with the right tool, not wood screws with a hex drive. A badly fitted insert pulls out and takes a plug of walnut with it.
Mark the depth on the drill bit

Boring through a slab you have spent a weekend flattening is a bad afternoon. Wrap tape round the bit at the depth you want and keep at least 20 mm of solid wood above the hole.

Blind cleats

A wooden or steel cleat is fixed to the underside of the slab, and the base hooks or bolts onto it from within the frame. Nothing is visible from outside.

The cleat must be attached to the slab in a way that allows movement itself, which means screws through slots in the cleat running across the grain, or the cleat runs along the length of the slab where movement is negligible. A cleat running across the width, screwed tight, is the classic way to crack a top.

French cleats

Two matching 45 degree bevelled battens, one on the piece and one on the base or wall, hooked together. Excellent for consoles, wall-mounted benches and shelves. Nothing visible, strong in the vertical direction, and the piece lifts off.

On a wall it is also the easiest way to spread load across multiple studs. For shelves specifically, see wall mounting a slab shelf.

Comparison

MethodVisibleAllows movementRemovableDifficulty
Screws through slots from inside the baseNothing from outsideYesYesEasy
Threaded inserts and machine screwsNothingYes, via base slotsYes, repeatedlyModerate
Blind cleatNothingOnly if slottedYesModerate
French cleatNothingYes, it can slideVeryEasy
Epoxy or glueNothingNoNoDo not

The simplest answer is usually enough

On a steel base with a top rail, screws going up through slotted holes in the rail are already invisible from every normal viewing angle. People reach for inserts and cleats to solve a problem that the frame already solves. Look at the base from a seated position before deciding you need something cleverer.

Think about taking it apart

A slab table will be moved, through doorways, between homes, possibly to a different base. Choose a fixing you can undo. Threaded inserts take repeated assembly far better than wood screws, which strip after three or four cycles in the same hole. If you expect to move it, inserts are the right answer for that reason alone rather than for looks.

Moving one is covered in carrying and lifting a slab safely.

Common questions

How do you attach a table top with no visible screws?

Screw up through slotted holes in the base frame, which is invisible from outside, or set threaded inserts into the underside of the slab and bolt up into them from within the frame.

Are threaded inserts strong enough for a heavy slab?

Yes, when they are inserts intended for hardwood, fitted square to a bored hole at the right depth. They also survive repeated assembly far better than wood screws.

Can I glue a slab top to its base?

No. The top must be able to change width with the seasons, and glue prevents it. A glued top cracks.

What is a French cleat?

Two matching bevelled battens that hook together, one on the furniture and one on the wall or base. It is invisible, strong, allows sideways movement and lets the piece lift off.

Every slab here is the only one of its kind

Walnut, oak and plane, up to 330 cm, kiln dried to 8 to 10 percent. Shortlist what fits and we send photos, measurements and a delivery quote within a day.

See slabs in stock