How Far a Slab Can Span Unsupported

Overhang beyond the base, sag over time and how thickness changes the maths. A practical rule to work from.

Bases and engineering6 min readUpdated 2026-10-23

Two questions hide inside this one. How far can the top hang past the base before it feels springy, and how far apart can the supports be before the middle sags over years. They have different answers, and the second one is the one that bites slowly.

The physics in one paragraph

Stiffness in a panel rises roughly with the cube of its thickness and falls roughly with the cube of the span. Doubling thickness gives about eight times the stiffness. Doubling the span gives about one eighth. That ratio is why a modest increase in thickness buys so much, and why moving the legs 20 cm further apart costs more than it looks.

Species matters less than people expect. Oak is stiffer than walnut, but not by enough to change a design decision. Thickness and span are the levers.

Overhang past the base

The end of the table is a cantilever. Somebody leans on it, or sits on it, and the leverage is all at the fixing. Keep within these and it will feel solid.

Finished thicknessComfortable overhangHard limit
4 cm30 cm40 cm
5 cm40 cm50 cm
6 cm45 to 50 cm60 cm
7 cm55 cm70 cm

These are about feel, not failure. The slab will not break at the hard limit; it will deflect enough that a person leaning on the corner notices the table move, and the fixings will take a cyclic load they were not designed for.

There is a competing requirement: you want the base inboard enough that end chairs are not fighting the legs. For a six-seat table, a base set about 45 cm in from each end usually satisfies both.

Distance between supports

Between the two pedestals, or between two pairs of legs, the top is a simple beam. This is where long-term sag happens, because wood under constant load deflects slowly and permanently. That process is called creep, and it is why a bookshelf that looked fine on day one has a visible dip after five years.

A dining top carries less load than a bookshelf, so creep is a slow problem rather than an urgent one. As a working guide for the gap between supports:

  • 5 cm top: keep supports within about 140 cm of each other.
  • 6 cm top: about 180 cm.
  • 7 cm top: about 220 cm.

On a 300 cm table with 45 cm overhangs, the gap between supports is 210 cm. At 6 cm thick that is beyond the comfortable guide, which is exactly why long tables at 6 cm often get a stretcher between the pedestals, or move to 7 cm.

The cheap fix

A steel stretcher or a flat bar let into the underside, running the length between supports, transforms a marginal span. It is invisible in use, costs very little and lets a 6 cm top handle a 300 cm table comfortably.

Where live edges change the numbers

A slab is not a rectangle. If it waists to 70 cm in the middle and is 100 cm at the ends, the narrow point is also the weakest point, and it is usually near the centre of the span where the bending is highest.

Two consequences:

  • Treat the narrow width as the effective beam when judging a long span.
  • If there is a big void or a through crack near mid span, reduce the span or add a stretcher. A void is a hole in the beam.

Kitchen islands and bars

Islands are the easy case, because cabinets support the top almost continuously. The only real span is the seating overhang, and there the limit is lower than a dining table because people put their full weight on it while getting onto a stool.

  • Up to 25 to 30 cm of overhang in a 5 cm top: no extra support.
  • 30 to 45 cm: steel flat bar let into the underside, or a plate bracket off the cabinet.
  • Over 45 cm: visible corbels or a leg.

A bar top is the same, with the complication that the front edge is in constant use. Support the back edge continuously and treat the front as a short cantilever.

Shelves are the hard case

A floating shelf carries proportionally far more load and holds it permanently, so creep dominates. A 4 cm slab shelf at 120 cm between fixings with books on it will sag visibly within a few years. Keep shelf spans short, or hide steel in them. See wall mounting a slab shelf.

How to check your own design

Before the base is made, lay the finished top on two supports at the planned spacing and put your weight on the middle and then on each end. If you can see it move or feel it give, change something: thicker top, closer supports, or a stretcher. Finding this out with the slab on two trestles costs nothing. Finding it out after the base is welded costs the base.

Common questions

How much can a table top overhang the base?

About 45 to 50 cm on a 6 cm top before the end starts to feel springy under a leaning adult, less on thinner tops. Structural failure is not the limit, perceived solidity is.

How far apart should table legs be?

Close enough that the span between them stays within roughly 140 cm at 5 cm thick, 180 cm at 6 cm and 220 cm at 7 cm, and far enough in from the ends that chairs are not fighting the legs. A stretcher between supports relaxes the first constraint.

Will a slab table sag over time?

Wood under constant load deflects slowly and permanently, which is called creep. On a dining top with a sensible span it is not a practical problem. On a long shelf carrying books it is the main design constraint.

Does thicker wood really help that much?

Yes. Stiffness rises with roughly the cube of thickness, so 6 cm is around 70 percent stiffer than 5 cm, not 20 percent. Small increases in thickness buy a lot of span.

Long slabs, up to 330 cm

If you want a three metre table, start from a slab with the thickness to carry it. Every listing gives length, both widths and thickness.

See slabs in stock