Steel Base Shapes for a Slab Top
U, A, X, trestle and pedestal. What each does to leg room, stability and how the table looks from across a room.
The base decides three things people notice every day: where the legs are when you sit down, whether the table wobbles, and how heavy the whole thing looks. The slab gets the attention and the base does the work.
The common shapes
| Shape | Legroom | Stability | Visual weight | Best for |
|---|---|---|---|---|
| U frame | Excellent, nothing at the corners | Good, needs a stretcher on long tables | Low | Dining tables, desks |
| A frame | Good, feet splay outward | Very good | Medium | Long dining tables |
| X frame | Good in the middle, legs cross at the ends | Very good | Medium to high | Statement dining tables |
| Trestle pair | Excellent at the ends | Good with a stretcher | Low to medium | Long tables, desks |
| Single pedestal | Perfect, nothing in the way | Needs a wide foot and mass | Low | Round tops, small tables |
| Four separate legs | Worst, a leg at every corner | Good | Low | Traditional look, small tables |
| Box or plinth | None, it is a solid block | Excellent | High | Consoles, benches, islands |
Work out where people sit first. On a six seat table, two of them sit at the ends, and a base with legs near the corners puts steel exactly where their knees go. That single fact rules out four separate legs for most slab dining tables and is why U frames and trestles dominate.
Setback from the ends
How far in from the end of the top the base sits is a compromise between two things. Set it too far in and the ends become springy cantilevers; set it too far out and the end chairs fight the base. For a typical 6 cm thick slab, 40 to 50 cm in from each end usually satisfies both. The overhang limits are in how much overhang a slab top needs, and the span question is in unsupported span and thickness.
Stretchers
Two separate frames or trestles will rack, meaning the table leans sideways when pushed, unless they are tied together. A stretcher between them fixes it completely.
- Low stretcher near the floor: maximum legroom, slight foot obstruction.
- Mid-height stretcher: stiffer, but people kick it.
- No stretcher: only if each frame is wide enough fore and aft, or the top itself is thick and stiff enough to resist racking.
Section size and finish
Thin flat bar looks elegant and flexes. Box section is far stiffer for the same visual weight. As a rule, a dining table base in box section around 40 by 40 mm or larger will feel solid; thinner than that and you are relying on the geometry.
Powder coat in matte black or a dark grey is the default and disappears under the slab. Raw or clear-lacquered steel looks good and will mark; bare steel against an oak top risks tannin staining where water sits, which is covered in keeping a pale oak top pale.
Heights
Order the base to the finished height you want minus the actual thickness of your slab. Our slabs are mostly 6 cm, some 5 and 7. Getting this wrong by one centimetre is the most common ordering mistake. The numbers are in base height for dining, desk and bar.
Feet
Adjustable feet are not optional on a hard floor. Almost no floor is flat, and a rigid four-point base on an uneven floor rocks. See levelling a table on an uneven floor. Wide flat feet also spread the load, which matters on a soft timber floor under a heavy slab.
Fixing to the top
Whatever the shape, the base must let the top move. Slotted holes in the top rails, not round ones. Covered in Z clips, figure-eight fasteners and slotted holes.
Common questions
What is the best base shape for a live-edge table?
A U frame or a pair of trestles for most dining tables, because neither puts steel where end-seat knees go. Four separate legs are the worst choice for seating six.
How far in from the end should a table base sit?
Around 40 to 50 cm from each end on a typical 6 cm slab. Closer in makes the ends springy; further out makes the end chairs fight the base.
Does a trestle base need a stretcher?
Two separate frames will rack sideways without one. A low stretcher near the floor gives maximum legroom and solves it completely.
What height base should I order?
The finished height you want minus the actual measured thickness of your slab. Measure the slab rather than assuming, since thickness varies.