Levelling a Table on an Uneven Floor
Adjustable feet, shimming and why a rigid four-leg base rocks where a trestle does not.
Almost no floor is flat. A table with four rigid feet on an uneven floor rocks, and no amount of moving it around the room fixes that. The solution is either adjustable feet or a base that only touches the floor in two places.
Why four points rock and three do not
Three points always define a plane. Four points only sit flat if the floor is flat, which it is not. That is the whole geometry of the problem and it is why a tripod camera stand never wobbles.
A trestle or U frame base touches the floor along two lines rather than at four points, which is more forgiving than four separate legs but still not immune. A single pedestal with a wide foot is the most forgiving of all.
Adjustable feet are the answer
Specify them when ordering a base. The usual form is a threaded bolt into a captive nut in the leg, with a swivel pad on the end.
- Ask for enough travel. 15 to 20 mm of adjustment covers most domestic floors. Short feet with 5 mm of travel run out on an old floor.
- Swivel pads, not fixed. A swivel pad sits flat on a sloping floor; a fixed one touches on one edge and marks it.
- Wide pads. They spread the load, which matters on soft floors. See floor loading and very heavy tables.
- A locknut stops the setting drifting as people lean on the table.
There are two different goals and people confuse them. You can make the top horizontal, or you can make the table stop rocking. On a sloping floor you often cannot have both without a visible gap under one foot. Choose: a rocking table is intolerable, a top that is 2 mm out of level over 3 metres is invisible.
The method
- Put the table in its final position with the top on, because the weight changes everything.
- Find the rock. Press each corner in turn. One diagonal pair will be solid and the other will move.
- Adjust one foot only. Wind down the foot that is off the floor until the rock stops. Do not touch the other three.
- Check with a spirit level along the length and the width. Correct if you can without reintroducing a rock.
- Lock the nuts.
- Check again in a week. Carpet compresses, timber floors settle, and feet bed in.
If the base has no adjustable feet
Shim it, properly rather than with a folded beer mat.
- Plastic or hardwood shims cut to the full footprint of the foot, not a corner of it.
- Glue the shim to the foot, not to the floor, so it moves with the table.
- Add a felt pad over the shim so the floor sees felt.
- Retrofit feet if the leg allows it. Drilling and tapping a steel leg for an adjustable foot is a straightforward workshop job and a permanent fix.
Carpet
A heavy table on carpet compresses the pile underneath and will appear to level itself over a week or two, then need a small adjustment. Level it, use it for a fortnight, then check again. Deep pile also hides a rock until someone leans on an end.
When the rock is not the floor
Check these before blaming the room:
- A twisted base. Stand it on a known flat surface such as a kitchen worktop and see whether all four feet touch.
- A cupped slab. If the top is not flat, the base is being twisted by the fixings. The cause is usually one face sealed and the other not, covered in seasonal movement and humidity.
- Overtightened fixings pulling a flat base into a non-flat top. Loosen and retighten with the base sitting naturally. See attaching a slab top to a base.
Common questions
How do I stop my table rocking?
Find which diagonal pair of feet moves, then wind down the single foot that is off the floor until the rock stops. Do not adjust the other three.
Why does a four-legged table rock but a trestle does not?
Three points always define a plane, four do not. A trestle or U frame touches along two lines instead of at four separate points, which is more forgiving on an uneven floor.
How much adjustment should table feet have?
15 to 20 mm of travel covers most domestic floors. Feet with only a few millimetres run out on older floors.
Should I level the table or stop it rocking?
Stop the rocking first. A top that is a couple of millimetres out of level across three metres is invisible, while a rocking table is used every day.