Building a Hallway Bench
Height, depth, span and a finish that survives wet shoes and bags being dropped on it.
A bench is the shortest route from a slab to a finished piece of furniture. There are no holes to cut, no cabinets to meet and no finish to agonise over. It is the project to do first if you have never built anything.
Dimensions
| Figure | Why | |
|---|---|---|
| Seat height | 45 to 47 cm | Same as a dining chair |
| Depth | 35 to 40 cm | Enough to sit on, not so much that it blocks a hall |
| Length per adult | 50 to 55 cm | 160 cm seats three comfortably |
| Thickness | 4 cm minimum | People sit heavily and sometimes stand on it |
| Support spacing | Under 120 cm between legs | Below that, sag is not a question |
Hallway depth is the constraint most people forget. A 40 cm bench in a 100 cm hall leaves 60 cm to walk past, which is tight with a coat on. Measure the hall first.
Not by you, by a child reaching a coat hook, or by whoever is hanging a picture. Design for a point load in the middle, which means either a slab 4 cm or thicker, or supports closer together. A seat that flexes when someone stands on it is unnerving even if it never breaks.
Order of work
- Acclimatise the slab indoors for two weeks.
- Flatten it, or have it flattened. For a bench, perfection is not required: this is a forgiving first project.
- Cut to length. Decide which end is which, since a live-edge slab is rarely symmetrical.
- Prepare both live edges, softening them properly, because legs brush against the front edge. See finishing the live edge itself.
- Sand, then finish all six faces.
- Fit legs with slotted holes.
Base options
- Two steel U frames. The default. Set them 20 to 30 cm in from each end.
- A pair of hairpin legs at each end. Light, cheap, and they flex sideways on a long bench. Fine up to about 120 cm.
- Solid timber slab legs. A heavy, monolithic look. Attach with slotted fixings, not glue.
- Wall mounted, floating. Dramatic and demanding: a bench takes far more load than a shelf, so masonry and heavy brackets only. See wall mounting a slab shelf.
Shapes compared in steel base shapes for a slab top.
The hallway problem: water
This is the one thing that makes a hall bench different from a bench anywhere else. Wet coats, wet bags, wet shoes if anyone sits and puts their feet up.
- Extra coats of finish, particularly on the top face and both ends.
- The underside matters more than usual, because a bench often sits against a cold external wall in a hall.
- Leave a gap behind it rather than pushing it tight to the wall, so air moves.
- Check it after the first winter. A hall is the coldest, dampest room in most houses.
Finish choice in hardwax oil, lacquer or epoxy: hardwax oil is still right here, because a hall bench picks up scratches and spot repair is the whole argument.
Which slab
A bench is the natural use for a narrower slab, which is cheaper per piece and harder to use for a table. Our W-23 walnut at 250 cm by about 74 cm would make a long bench and have plenty left over, and C13 at 210 cm is bench-shaped already. Species notes in oak bench slab and walnut bench slab.
Good second use
Because a bench is short, one slab often yields a bench and a console, or a bench and a coffee table. Plan both cuts before you make the first one, and keep the offcut for test finishing, which is advice that pays off years later when something needs repairing.
Common questions
How high should a hallway bench be?
45 to 47 cm, the same as a dining chair. Deeper than 40 cm starts to block a narrow hall.
How thick does a bench slab need to be?
4 cm minimum, because people sit heavily and sometimes stand on it. With supports under 120 cm apart, sag is not a concern at that thickness.
How long a bench do I need for three people?
About 160 cm, allowing 50 to 55 cm per adult.
What finish for a hallway bench?
Hardwax oil with extra coats on the top and ends, because a hall is damp and a bench collects scratches that spot repair handles well.