Raised Grain After the First Coat
Why the surface feels rough after coat one, and the de-nibbing step that fixes it for good.
You sand a slab to 180, it feels like silk, you put the first coat on, and the next morning it feels like fine sandpaper. Nothing has gone wrong. This happens to every piece of wood and there is one small step that deals with it permanently.
Why it happens
Sanding does not cut every fibre off cleanly. Some get bent over and compressed against the surface. They look and feel flat. When liquid reaches them they absorb it, swell, and stand back up, which is why the surface feels rough only after the first wet coat.
It is worse on open-pored species such as oak and plane than on walnut, and worse on end grain and the live edge than on the face.
The fix: de-nib after coat one
- Let the first coat cure as long as the data sheet says, usually overnight.
- Work the surface with a fine abrasive pad or worn fine paper, along the grain, with light pressure. A grey or white non-woven pad is the usual tool.
- You are knocking the tops off standing fibres, not sanding the wood. The surface goes smooth again within a few passes.
- Vacuum and wipe to get the dust off.
- Apply coat two. It will not raise again, because the fibres that were going to stand up already did and have been removed.
Two minutes per square metre. This step is the difference between a top that feels good and a top that feels slightly gritty forever.
The temptation is to go back to 180 paper and sand properly. Do not. The first coat has cured into the surface fibres and sanding it back means removing finish, re-exposing bare wood unevenly, and starting again. Light pressure, fine abrasive, along the grain.
Water popping: doing it before the finish instead
You can raise the grain deliberately while the wood is still bare, cut it back, and then finish. This is called water popping.
- Finish sanding at your final grit.
- Wipe the surface evenly with a damp, not wet, cloth.
- Let it dry fully, which can take a couple of hours.
- Cut the raised fibres back with the same final grit, lightly.
- Now finish.
Worth it under a film finish, where a rough first coat is harder to correct. Optional under hardwax oil, where de-nibbing after coat one does the same job with less fuss. Grit choices are in the sanding sequence for a slab top.
Where it is worst
| Surface | How much it raises | What to use |
|---|---|---|
| Face grain, walnut | Least | Fine abrasive pad |
| Face grain, oak and plane | Moderate | Fine abrasive pad |
| End grain | More | Pad, and expect a second de-nib |
| Live edge | Most | Brass brush and hand pads, see finishing the live edge |
If it is still rough after coat two
Two likely causes. Either the de-nib was too gentle and some fibres survived, in which case repeat it and apply a third thin coat. Or you left surplus finish on the surface and it cured into a gritty film with dust in it, which is the problem described in applying hardwax oil to a slab top. Those feel different: raised grain is a uniform fine texture, cured surplus is patchy and slightly sticky.
Dust is the other cause of roughness
A top finished in a room where a sander was running an hour earlier will have dust cured into the first coat, and it will feel rough for exactly the same reason it would have on a lacquered surface. Vacuum the room, let the air settle, then coat.
Common questions
Why is my table rough after the first coat of oil?
Raised grain. Sanding bends some fibres over rather than cutting them; the first wet coat makes them swell and stand up. It is normal and expected.
How do you fix raised grain?
After the first coat has cured, work the surface lightly along the grain with a fine non-woven abrasive pad, remove the dust, and apply the next coat. The grain will not raise again.
Should I sand between coats of hardwax oil?
Not a real sanding. De-nib with a fine pad, which knocks the tops off standing fibres without cutting back into the cured coat.
What is water popping?
Deliberately wetting the sanded bare wood to raise the grain, letting it dry, then cutting it back before finishing. It is useful under film finishes and optional under hardwax oil.