Building a Slab Desk
Cable routing, depth, monitor arms and the fixings that let you clamp things to the edge without splitting it.
A desk is the slab project people live with most closely. You are touching it for eight hours a day, which raises the bar on the finish and on the edge, and lowers it on everything else: a desk is structurally the easiest slab build there is.
Dimensions that work
| Minimum | Comfortable | Notes | |
|---|---|---|---|
| Depth | 60 cm | 70 to 80 cm | Below 60 cm a monitor is too close |
| Width | 120 cm | 140 to 180 cm | 160 cm fits two monitors and room to write |
| Finished height | 73 cm | 73 to 75 cm | With an adjustable chair |
| Thickness | 4 cm | 5 to 6 cm | Thicker eats thigh clearance |
Thickness is a real trade-off on a desk in a way it is not on a dining table, because your thighs are under it all day. A 7 cm slab at 74 cm leaves the underside at 67 cm, which is tight for a tall person. See base height for dining, desk and bar.
Order of work
- Acclimatise the slab in the room for at least two weeks before cutting anything. See acclimatising a slab after delivery.
- Flatten it, with a router sled if you are doing it yourself. Method in flattening a slab with a router sled.
- Cut to length and decide which live edge faces you.
- Cut any cable holes now, while the slab is on trestles and you can get under it.
- Prepare the live edge, which on a desk means smoother than usual because forearms rest on it. See finishing the live edge itself.
- Sand through the grits and finish all six faces.
- Fit the base with slotted holes.
Most people put the live edge at the front, where they see and touch it. That edge then has to be comfortable under wrists and forearms for years, which means softening it more than you would on a dining table. If you want a dramatic raw edge, put it at the back and cut the front edge straight.
Cable management
Decide this before finishing, because every option involves cutting.
- Grommet holes: a 60 or 80 mm hole saw at each end, 10 to 15 cm in from the back edge. Simple and reversible in the sense that a grommet hides the edge.
- A slot at the back: routed rebate along the rear underside, so cables drop behind and nothing shows on the surface. Tidier, more work.
- An under-desk tray screwed to the underside, which holds a power strip and the mess. The best answer for a desk with a lot of kit.
- Nothing: defensible on a desk with a laptop and no monitor, and regretted the day you add one.
Seal the inside of every hole you cut. Bare end grain inside a grommet hole takes moisture and dirt.
Monitor arms and the edge
A clamp-on monitor arm grips the back edge of the desk, and that is a concentrated load on a thin area.
- A 5 or 6 cm slab takes a clamp fine, provided the clamp has a wide jaw.
- Put a pad under the jaw, hard rubber or leather, or the clamp will print into the finish within a week.
- Check the clamp opens far enough. Many monitor arms max out around 6 cm and will not fit a 7 cm slab. Measure before buying.
- Through-desk mounting is the alternative: a hole through the slab and a bolt. Stronger, permanent, and it must be drilled square.
- The live edge is not a clamping surface. If the live edge is at the back, you need a straight section to clamp or a through mount.
Base choice
A desk sees sideways loads nothing else does: you push off it to stand up, you lean on one end. A U frame or a pair of trestles with a stretcher resists that. Four separate legs on a desk rack unless they are substantial. Shapes in steel base shapes for a slab top.
Standing desk frames exist that take a heavy top, and the weight limit is the thing to check: many are rated for 70 to 80 kg, which a large slab approaches on its own.
The finish for a desk
Hardwax oil, matte, and more coats than you would put on a dining table, because forearm contact wears a finish quickly. Expect to refresh the area in front of the chair before the rest. See maintaining an oiled slab top.
Common questions
How deep should a slab desk be?
60 cm minimum, 70 to 80 cm comfortable. Below 60 cm a monitor sits too close to the eye.
How thick should a desk slab be?
4 to 6 cm. Thicker looks good and eats thigh clearance, which matters on a desk because you are under it for hours.
Can you clamp a monitor arm to a live-edge desk?
To a straight section, yes, with a pad under the jaw. Check the clamp opens far enough, since many stop at around 6 cm. The live edge itself is not a clamping surface.
When should I cut the cable holes?
Before finishing, while the slab is on trestles and you can reach underneath. Seal the inside of every hole.