Tools You Actually Need for a Slab Build

The short list that gets a slab from rough-sawn to finished, and the expensive tools you can hire instead.

Build guides4 min readUpdated 2026-10-23

The tool list for a slab table is shorter than people expect, because a slab arrives as one piece of wood. There is no jointing, no glue-up and no panel work. Most of the job is removing material and then finishing.

The genuinely essential list

ToolForNotes
Random orbit sanderEverything after flattening150 mm, with extraction. The tool you will use most
Circular saw and a straightedge guideCutting to lengthA track saw is better and not essential
Drill driverFixing the basePlus a decent set of bits
Long straightedge, 1.5 m or moreChecking flatYou cannot judge flat by eye
ClampsHolding everythingMore than you think
Work lightRaking light to see scratchesThe cheapest quality improvement available
Mask, eye and ear protectionNot optionalSlab dust is a lot of dust
A work light is the best value purchase on this list

Every sanding mistake is invisible under normal room lighting and obvious under a lamp shone almost flat across the surface. People buy a better sander when what they needed was to see what the sander was doing.

The expensive one: flattening

This is the only operation that genuinely needs a tool you probably do not own. Three options:

  1. Pay a workshop. A wide belt sander or a CNC does it in an hour, and this is often cheaper than building a sled you use once.
  2. Build a router sled. Needs a big router, straight rails and a day. Covered in flattening a slab with a router sled.
  3. Hire. A large router is a common hire item.

Worth having, not essential

  • Track saw. Makes end cuts clean and square with no setup. If you will build more than one piece, buy one.
  • Card scraper. A few pounds, and the right tool for levelling a resin fill flush without dishing the wood around it. See filling voids and knots with resin.
  • Brass brush in a drill. For live edge preparation, covered in finishing the live edge itself.
  • Router with a round-over bit. For easing the top arris.
  • Moisture meter. Reassurance rather than necessity if you buy kiln dried, and useful if a slab has been stored somewhere damp. See moisture content explained.
  • Hole saw set. For cable holes and taps.
  • Lifting straps. Turn a four-person carry into a two-person one, as described in carrying and lifting a slab safely.

What you do not need

  • A planer or thicknesser. Nothing you own will take a 90 cm wide slab.
  • A jointer. There is nothing to joint.
  • A table saw. You cannot safely cross-cut a 110 kg slab on one.
  • A domino or biscuit jointer. No joinery in a one-piece top.
  • Hundreds of abrasive grits. Four, in sequence, as in the sanding sequence for a slab top.

Consumables, which cost more than people budget

Sanding discs in quantity, because a worn disc burnishes instead of cutting. Lint-free cloths for the finish. The finish itself, which covers a surprising area per litre. Hot glue sticks and shim material if you are flattening. Budget for discs: a large slab goes through many more than a small project.

The realistic minimum

Buy the flattening as a service, own a random orbit sander, a circular saw with a straightedge, a drill, a long straightedge and a work light, and you can build a slab dining table in a garage. That is a shorter list than almost any other piece of furniture.

Common questions

What tools do I need to make a slab table?

A random orbit sander, a circular saw with a straightedge, a drill, a long straightedge, clamps and a work light. Flattening is the only operation that needs a tool most people do not own.

Do I need a planer for a wood slab?

No, and nothing domestic will take a slab that wide. Flattening is done with a router sled or by a workshop with a wide belt sander.

Is it cheaper to pay someone to flatten a slab?

Often, if you would otherwise build a sled and buy a large router for a single project. Compare the hire or workshop cost against the tools before deciding.

What is the most underrated tool for this?

A work light. Shone almost flat across the surface it reveals every sanding scratch and dip that room lighting hides and the finish will magnify.

Every slab here is the only one of its kind

Walnut, oak and plane, up to 330 cm, kiln dried to 8 to 10 percent. Shortlist what fits and we send photos, measurements and a delivery quote within a day.

See slabs in stock