Mistakes People Make on a First Slab

Finishing too soon, sanding too fine, fixing it down rigid and five others we see most often.

Build guides4 min readUpdated 2026-10-23

Most first slab projects go well. The ones that do not nearly always fail for one of a short list of reasons, and every one of them is avoidable by knowing about it beforehand.

1. Cutting it the week it arrives

A slab that has travelled from a workshop to a lorry to your garage has been through several different environments. Give it at least two weeks flat on battens in the room where it will live, and longer if the house is very dry or the slab came from somewhere very different. Cut before that and the piece changes shape after you have built it. See acclimatising a slab after delivery.

2. Screwing it down rigidly

The single most expensive mistake. A solid top must be able to change width with the seasons, and a top fixed through round holes at both ends will crack, usually in its first winter. Slotted holes, one rigid point at the centre. See Z clips, figure-eight fasteners and slotted holes.

If you remember one thing

The wood moves. Every design decision on the underside of a slab table is about allowing that. Nothing glued across the grain, nothing screwed tight at both ends, nothing clamped flat.

3. Sanding too fine

Going to 320 feels like care and it closes the surface so the oil cannot penetrate. The result is a thinner, paler finish, and on walnut a top that never reaches the colour you saw on the test piece. Stop where the product asks, usually 150 to 180. See the sanding sequence for a slab top.

4. Leaving the finish on the surface

Hardwax oil goes in the wood and the surplus is wiped off. Leave a film to cure and you get sticky patches that take weeks to harden and have to be dissolved off. This is the most common finishing failure by a wide margin. Method in applying hardwax oil to a slab top.

5. Not finishing the underside

Nobody sees it, and it still exchanges moisture with the room. A top sealed on one face and bare on the other takes up and releases moisture at different rates and cups. All six faces, every time.

6. Using the table before the finish has cured

Dry to touch is not cured. A plant pot on a week-old oiled top leaves a ring that a cured surface would have shrugged off, and a tablecloth laid on it can emboss the finish. Give it the full cure time from the data sheet, which is weeks rather than days. See dry to touch versus fully cured.

7. Ordering the base before measuring the slab

Flattening removes 3 to 8 mm per face, so a slab listed at 6 cm can finish at 5.4 cm. Base height is the finished height minus the actual thickness, measured after flattening. See base height for dining, desk and bar.

8. Filling cracks too early

A crack that opened because the air is dry will close again when humidity rises, and resin poured into it in February is compressed in June. Wait a season before filling anything that appeared after the piece was built. See a new crack has appeared: what now.

9. Not testing on an offcut

Ten minutes finishing a scrap tells you the colour, the sheen, how much the edge drinks and whether you like the result. Every one of those is expensive to discover on the table. Keep the offcut afterwards as the reference for future repairs.

10. Doing it in a cold garage in December

Oil finishes cure by reacting with air and effectively stall below about 15 degrees. A top finished in an unheated space in winter can stay tacky for weeks and never fully harden. Sand in the cold if you must, finish in the warm.

The pattern

Eight of these ten are about patience: letting the wood settle, letting the finish cure, waiting a season before filling, testing before committing. Slab work rewards slowness more than skill, which is why it is a good project for a first-time maker with a straightedge and a sander.

Common questions

What is the most common mistake with a slab table?

Fixing the top down rigidly so it cannot change width with the seasons. That is what cracks tops, usually in the first winter.

How long should I wait before cutting a new slab?

At least two weeks flat on battens in the room where it will live, longer if the house is very dry.

Can I sand a slab to 320 grit?

You can, and the finish will be worse. Fine sanding closes the surface so oil cannot penetrate, giving a thinner and paler result. Stop at the grit the product specifies.

Why is my new table sticky?

Surplus finish was left on the surface instead of being wiped off, or it was applied in a cold room. Both leave a soft film that takes weeks to harden.

Every slab here is the only one of its kind

Walnut, oak and plane, up to 330 cm, kiln dried to 8 to 10 percent. Shortlist what fits and we send photos, measurements and a delivery quote within a day.

See slabs in stock