How to Read a Slab Listing

Length, the two widths, thickness, species and the note. What each field is really telling you.

Choosing a slab5 min readUpdated 2026-10-23

A slab listing is a short block of numbers that decides whether a piece suits your project. Most of the information is in how the numbers are presented, not just their values.

The fields, and what each one means

FieldWhat it tells you
SpeciesWalnut, oak or plane here. Decides colour, hardness and how it ages.
CodeThe slab's identity. C16 is a specific piece, not a product line. There is one of it.
LengthOverall, including any end checks that will be trimmed.
WidthsUsually three numbers: one end, the middle, the other end. This is the most important field.
ThicknessRough sawn. Subtract 3 to 6 mm for flattening, more if the slab has twist.
TypeSlab, pair or cookie. A cookie is cut across the trunk and behaves differently: cross-cut rounds.
PricePer slab, without VAT. Pairs are priced together.
NoteThe written description of what the slab actually has. Read it twice.

Three widths, not one

This is the field that decides what you can make, and the one most often misread.

A slab listed as 90, 108, 96 means roughly 90 cm at one end, 108 cm in the middle and 96 cm at the other. Three facts follow:

  1. The narrow point governs. If you need a 100 cm wide dining table, this slab does not give it, because one end is 90 cm. The widest number is the least useful one.
  2. Where the narrow point sits matters. A slab narrow in the middle is awkward for a table and interesting for a river table. A slab narrow at one end can be cut shorter to lose it.
  3. These are the extremes of a curve. A live edge is continuous, so the slab is not 90 cm for the first third. It transitions, and the photographs show the shape.

Rough sawn thickness is not finished thickness

Every slab here is supplied rough sawn, meaning as it came off the mill. Your maker flattens both faces, and that removes material.

  • A flat slab: 3 to 6 mm total loss. 6 cm finishes around 5.4 to 5.7 cm.
  • A cupped or bowed slab: more, because flattening works down to the lowest point.
  • A twisted slab: considerably more, sometimes 10 to 15 mm, because the whole face has to come down to clear the worst corner.

So "6 cm" is a starting point, not a specification. If the finished thickness is critical, ask about flatness: how thick should a slab table be.

The note is where the real information is

The numbers describe the envelope. The note describes the wood. Things worth reading closely:

  • Shape language. "Waisted", "dramatic S-curve", "wide at both ends" all describe the live edge, which is most of what you are buying: what live edge actually means.
  • Defect language. "Burl pocket", "check", "void". Ask whether a crack goes through the thickness: cracks, checks and voids.
  • Colour language. "Dark heart runs the full length" tells you where the heartwood sits relative to the sapwood: sapwood and heartwood.
  • Suggested uses. "River table or a desk" is the seller telling you what the proportions suit.

What a listing cannot tell you

Four things to ask for if they matter:

  1. Flatness. Cup, bow and twist. Ask for a straightedge photograph.
  2. Moisture reading, method and date. See moisture content explained.
  3. The other face. Slabs have two, and they differ. The listing photograph shows one.
  4. Weight. Rarely listed, always relevant on delivery day. Work it out: what a slab weighs.

Working from the listing to your project

The sequence that avoids disappointment:

  1. Write down the finished dimensions you need.
  2. Add the trim you will lose at the ends.
  3. Compare against the narrow width, not the headline width.
  4. Subtract the flattening loss from the thickness.
  5. Check the route into the building: measuring your door and stairwell.

Common questions

Why not just list one width?

Because a slab does not have one width. A single average number would hide exactly the information that decides whether it works for your table.

Does the length include the bark ends?

The length is the overall piece. End checks and ragged ends come off when it is cut to length, so plan on losing a few centimetres at each end.

Can I ask for a slab to be cut before delivery?

Ask. Cutting to length can make delivery far easier on a long slab, and it is not reversible, so plan it carefully first.

Read a real one

Every slab lists species, length, three widths, thickness and a written note. Open one and the numbers below will make sense immediately.

Open C16